Table of Contents
Advertisement
91: Limiter - Cho/Flng
(Limiter - Chorus/Flanger)
This effect combines a mono limiter and a chorus/flanger. You
can change the order of the effects.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Routing
Limiter
+
Limiter
EQ Trim
LEQ HEQ
Gain Adjust
Right
Envelope - Control
LIMITER
1.0 : 1...
[L]Ratio
50.0 : 1, Inf : 1
a
Threshold [dB] –40...0
[L]Attack
1...100
b
Release
1...100
[L]Gain Adjust
–Inf,
c
[dB]
–38...+24
CHORUS/FLANGER
[F]LFO
0.02...20.00
Frequency [Hz]
d
LFO Waveform Triangle, Sine
[F]Delay Time
0.0...1350.0
[msec]
e
Depth
0...100
Feedback
–100...+100
f
[F]EQ Trim
0...100
[F]Pre LEQ
–15...+15
Gain [dB]
g
Pre HEQ Gain
–15...+15
[dB]
-Wet, -
[F]Cho/Flng
1:99...Dry...99:1
Wet/Dry
, Wet
h
Src
Off...Tempo
Amt
–100...+100
[F]Output
Normal,
Mode
Wet Invert
Limiter
i
Flanger,
Routing
Flanger
Limiter
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src
Off...Tempo
Amt
–100...+100
FX Amt
Chorus/Flanger
Chorus/Flanger
Normal
+
Output Mode
–
Wet Invert
Feedback
Cho/Flng FX Amt
FX Amt
LFO: Tri / Sine
Sets the signal compression ratio
Sets the level above which the
compressor is applied
Sets the attack time
Sets the release time
Sets the limiter output gain
Sets the speed of the LFO
Selects the LFO Waveform
Sets the delay time
Sets the depth of LFO modulation
Sets the feedback amount
Sets the EQ input level
Sets the gain of Low EQ
Sets the gain of High EQ
Sets the effect balance of the
chorus/flanger
Selects the Wet/Dry modulation
source for the chorus/flanger
Sets the Wet/Dry modulation
amount for the chorus/flanger
Selects the output mode for the
chorus/flanger
Switches the order of the limiter and
chorus/flanger
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source
Mono-Mono Serial (Mono-Mono)
92: Limiter - Phaser
This effect combines a mono limiter and a phaser. You can
change the order of the effects.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Limiter
+
Limiter
Gain Adjust
Right
Envelope - Control
LIMITER
1.0 : 1...
[L]Ratio
50.0 : 1, Inf : 1
a
Threshold [dB] –40...0
[L]Attack
1...100
b
Release
1...100
[L]Gain Adjust
–Inf,
c
[dB]
–38...+24
PHASER
[P]LFO
0.02...20.00
Frequency [Hz]
d
LFO Waveform Triangle, Sine
[P]Manual
0...100
e
Depth
0...100
Resonance
–100...+100
-Wet, -
[P]Phaser Wet/
1:99...Dry...99:1
Dry
, Wet
f
Src
Off...Tempo
Amt
–100...+100
[P]Output
Normal,
g
Mode
Wet Invert
Limiter
h Routing
Phaser, Phaser
Limiter
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
Effects
335
FX Amt
Routing
Phaser
Phaser
Normal
+
Output Mode
–
Wet Invert
Resonance
Phaser FX Amt
FX Amt
LFO: Tri / Sine
Sets the signal compression ratio
Sets the level above which the
compressor is applied
Sets the attack time
Sets the release time
Sets the limiter output gain
Sets the speed of the LFO
Selects the LFO Waveform
Sets the frequency to which the
effect is applied
Sets the depth of LFO modulation
Sets the resonance amount
Sets the phaser effect balance
Selects the phaser's Wet/Dry
modulation source
Sets the phaser's Wet/Dry
modulation amount
Selects the phaser output mode
Switches the order of the limiter and
phaser
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source
Advertisement
Table of Contents
