Korg Pa300 User Manual page 255

Slope
This parameter specifies the time over which the volume will
change from when it reaches the break point level until it reaches
the sustain level.
0...99 Time value.
Release
This parameter specifies the time over which the volume will
change after note-off until it reaches 0.
0...99 Time value.
Level Modulation
Amp 1 EG changes (Level) (AMS=Velocity, Intensity = a positive (+) value)
Note-on Note-on
Note-off
Softly played note when Start Level Strongly played note when Start Level
Swing=0 and Attack Level Swing Swing=0 and Attack Level Swing and
and Break Level Swing are set to + Break Level Swing are set to +
AMS (Alternate Modulation Source)
This parameter specifies the source that will control the "Level"
parameters of the amp EG. See "AMS (Alternate Modulation
Source) list" on page 256.
Intensity
This parameter specifies the depth and direction of the effect
that "AMS" will have. For example, if "AMS" is Velocity, setting
"St (Start Level Swing)", "At (Attack Level Swing)" and "Br
(Break Point Level Swing)" to + and setting "Intensity" to a posi-
tive (+) value will cause the amp EG volume levels to increase as
you play more strongly. Setting "Intensity" to a negative (–) val-
ues will cause the amp EG volume levels to decrease as you play
more strongly. With a setting of 0, the levels will be as specified
on "Amp: Amp EG".
-99...+99 Intensity value.
St (Start Level Swing)
This parameter specifies the direction in which "AMS" will
change "Start". If "Intensity" is set to a positive (+) value, setting
this parameter to + will allow AMS to increase the EG level, and
setting this parameter to – will allow AMS to decrease the EG
level. With a setting of 0, no change will occur.
At (Attack Level Swing)
This parameter specifies the direction in which "AMS" will
change "Attack". If "Intensity" is set to a positive (+) value, set-
ting this parameter to + will allow AMS to increase the EG level,
and setting this parameter to – will allow AMS to decrease the
EG level. With a setting of 0, no change will occur.
Br (Break Point Level Swing)
This parameter specifies the direction in which "AMS" will
change "Break". If "Intensity" is set to a positive (+) value, setting
this parameter to + will allow AMS to increase the EG level, and
setting this parameter to – will allow AMS to decrease the EG
level. With a setting of 0, no change will occur.
Note-on
Note-off Note-off
Strongly played note when Start Level
Swing=0 and Attack Level Swing and
Break Level Swing are set to +
Time Modulation
These parameters let you use an alternate modulation source to
modify the amp EG times that were specified in "Time" on
page 250.
Amp 1 EG changes (Time)
(AMS=Amp KTrk +/+, Intensity = a positive (+) value)
(When Amp Keyboard Track "Low Ramp"= a positive (+) value, and
"High Ramp" = a positive (+) value)
Note-on Note-on
Note-off
Low-pitched note played with
Attack, Decay, Slope, and
Release Time Swing at +
Amp 1 EG changes (Time) (AMS=Velocity, Intensity= a positive (+) value)
Note-on Note-on
Note-off
Softly played note with Strongly played note with
Attack, Decay, Slope and Attack, Decay, Slope and
Release Time Swing at + Release Time Swing at +
AMS1 (Alternate Modulation Source 1 - Time)
This parameter specifies the source that will control the "Time"
parameters of the amp EG (see "AMS (Alternate Modulation
Source) list" on page 256). With a setting of Off, there will be no
modulation.
Intensity
This parameter specifies the depth and direction of the effect
that "AMS1" will have. For example, if "AMS1(T)" is Amp KTrk
+/+, the (Amp) Keyboard Track settings (see "Keyboard Track-
ing" on page 249) will control the EG "Time" parameters. With
positive (+) values of this parameter, positive (+) values of
"Ramp (Ramp Setting) will cause EG times to be lengthened,
and negative (–) values of "Ramp (Ramp Setting)" will cause EG
times to be shortened. The direction of the change is specified by
"At (Attack Time Swing)", "Dc (Decay Time Swing)", "Sl (Slope
Time Swing)", and "Rl (Release Time)".
When "AMS1(T)" is Velocity, positive (+) values will cause EG
times to lengthen as you play more strongly, and negative (–)
values will cause EG times to shorten as you play more strongly.
With a setting of 0, the EG times will be as specified by the
"Level" parameters (see page 250).
At (Attack Time Swing)
This parameter specifies the direction of the effect that "AMS1"
will have on "Attack". With positive (+) values of "Intensity", set-
ting this parameter to + will allow AMS1 to lengthen the time,
and setting it to – will allow AMS1 to shorten the time. With a
setting of 0 there will be no effect.
Dc (Decay Time Swing)
This parameter specifies the direction of the effect that "AMS1"
will have on "Decay". With positive (+) values of "Intensity", set-
ting this parameter to + will allow AMS1 to lengthen the time,
and setting it to – will allow AMS1 to shorten the time. With a
setting of 0 there will be no effect.
Sound Edit 251
Amp: Amp EG
Note-on
Note-off Note-off
High -pitched note played with
Attack, Decay, Slope, and
Release Time Swing at –
Note-on
Note-off Note-off
Strongly played note with
Attack, Decay, Slope and
Release Time Swing at –