Download Print this page

Advertisement

352
Effects
Double Size
"Times. " Even in this case, the delay time cannot exceed 10,800
msec.
"Hold" procedure (when Loop Time = Auto)
1.
"Rec Src"JS +Y: #01
"Reset Src"JS –Y: #02
"Manual REC Control"REC Off
"Manual RST Control"RESET
"Loop Time [msec]"Auto
"MIDI/Tempo Sync"Off
It should be noted that all recordings will be deleted while
Reset is On.
"Manual RST Control"Off
2.
Reset is cancelled and the unit enters Rec ready mode.
3.
Push the joystick in the +Y direction (forward) and play a
phrase you wish to hold. When you pull the joystick to its
original position, the recording will be finished and the
phrase you just played will be held.
Loop Time is automatically set only for the first recording
after resetting. If the time length exceeds 10,800msec, Loop
Time will be automatically set to 10,800msec. (If you have
set "Times" to 1–10,800msec, the specified loop time will
be used regardless of the time taken from pushing the joy-
stick forward until it is pulled back. However, the recording
method remains the same. The phrase being played while
the joystick is pushed forward will be held.)
4.
If you made a mistake during recording, pull the joystick in
the –Y direction (back) to reset. In this way, the recording
will be erased. Repeat step 4. again.
5.
The recorded phrase will be repeated again and again. You
can use this to create an accompaniment.
By pushing the joystick in the +Y direction (forward), you
6.
can also overdub performances over the phrase that is
being held.
e: REC Control Src
g: Manual REC Control
"REC Control Src" selects the modulation source that controls
recording.
If this modulation is on, or if "Manual REC Control" is set to On,
you can record the input signal. If a recording has already been
carried out, additional signals will be overdubbed.
The effect is off when a value for the modulation source specified for
the "REC Control Src" parameter is 63 or smaller, and the effect is on
when the value is 64 or higher.
f: RST Control Src
h: Manual RST Control
The "RST Control Src" parameter specifies the modulation
source that controls the reset operation.
When you set this modulation source to On, or "Manual RST
Control" to RESET, you can erase what you recorded. If the Loop
Time parameter has been set to Auto, the loop time is also reset.
The effect is off when a value for the modulation source specified for
the "RST Control Src" parameter is 63 or smaller, and the effect is on
when the value is 64 or higher.
123: LCR BPM Long Dly
The L/C/R delay enables you to match the delay time with the
song tempo.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Left
Input Level D-mod
+
High Damp Low Damp
Input Level D-mod
Right
Tempo
BPM
Base Note x Times
BPM
Base Note x Times
Base Note x Times
MIDI,
BPM
40.00...
300.00
a
Time Over?
---, OVER!
L Delay Base
r...w
Note
b
Times
x1...x32
Level
0...50
C Delay Base
r...w
Note
c
Times
x1...x32
Level
0...50
R Delay Base
r...w
Note
d
Times
x1...x32
Level
0...50
Feedback
–100...+100
(C Delay)
e
Src
Off...Tempo
Amt
–100...+100
High Damp [%] 0...100
f
Low Damp [%] 0...100
Input Level
–100...+100
Dmod [%]
g
Src
Off...Tempo
h Spread
0...50
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
a: Time Over?
You can set the delay time up to 10,920msec. If the delay time
exceeds this limit, the error message "OVER!" appears in the dis-
play. Set the delay time parameters so that this message will not
appear. "Time Over?" is only a display parameter.
FX Amt
L Delay
Level
C Delay
Spread
Level
Feedback
R Delay
Level
FX Amt
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Displays an error message when the
delay time exceeds the upper limit
Selects the type of notes to specify
the delay time for TapL
Sets the number of notes to specify
the delay time for TapL
Sets the output level of TapL
elects the type of notes to specify
the delay time for TapC
Sets the number of notes to specify
the delay time for TapC
Sets the output level of TapC
Selects the type of notes to specify
the delay time for TapR
Sets the number of notes to specify
the delay time for TapR
Sets the output level of TapR
Sets the feedback amount of TapC
Selects the modulation source for
the TapC feedback
Sets the modulation amount of the
TapC feedback
Sets the damping amount in the
high range
Sets the damping amount in the low
range
Sets the modulation amount of the
input level
Selects the modulation source for
the input level
Sets the width of the stereo image
of the effect sound
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source

Advertisement

   Also See for Korg Pa300

   Related Manuals for Korg Pa300

Comments to this Manuals

Symbols: 0
Latest comments: