Table of Contents
Advertisement
322
Effects
Delay
65: L/C/R BPM Delay
The L/C/R delay enables you to match the delay time with the
song tempo. You can also synchronize the delay time with the
arpeggiator or sequencer. If you program the tempo before per-
formance, you can achieve a delay effect that synchronizes with
the song in real-time. Delay time is set by notes.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Left
Input Level D-mod
+
High Damp Low Damp
Input Level D-mod
Right
Tempo
BPM
Base Note x Times
BPM
Base Note x Times
Base Note x Times
MIDI,
BPM
40.00...
300.00
a
Time Over?
---, OVER!
L Delay Base
r...w
Note
b
Times
x1...x32
Level
0...50
C Delay Base
r...w
Note
c
Times
x1...x32
Level
0...50
R Delay Base
r...w
Note
d
Times
x1...x32
Level
0...50
Feedback
–100...+100
(C Delay)
e
Src
Off...Tempo
Amt
–100...+100
High Damp [%] 0...100
f
Low Damp [%] 0...100
Input Level
–100...+100
Dmod [%]
g
Src
Off...Tempo
h Spread
0...50
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
a: Time Over?
You can set the delay time up to 5,460msec. If the delay time
exceeds this limit, the error message "OVER!" appears in the dis-
play. Set the delay time parameters so that this message will not
appear. "Time Over?" is only a display parameter.
FX Amt
L Delay
Level
C Delay
Spread
Level
Feedback
R Delay
Level
FX Amt
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Displays an error message when the
delay time exceeds the upper limit
Selects the type of notes to specify
the delay time for TapL
Sets the number of notes to specify
the delay time for TapL
Sets the output level of TapL
elects the type of notes to specify
the delay time for TapC
Sets the number of notes to specify
the delay time for TapC
Sets the output level of TapC
Selects the type of notes to specify
the delay time for TapR
Sets the number of notes to specify
the delay time for TapR
Sets the output level of TapR
Sets the feedback amount of TapC
Selects the modulation source for
the TapC feedback
Sets the modulation amount of the
TapC feedback
Sets the damping amount in the
high range
Sets the damping amount in the low
range
Sets the modulation amount of the
input level
Selects the modulation source for
the input level
Sets the width of the stereo image of
the effect sound
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source
66: Stereo BPM Delay
This stereo delay enables you to set the delay time to match the
song tempo.
Stereo In - Stereo Out
Left
Input Level D-mod
Input Level D-mod
Right
Tempo
BPM
Base Note x Times
Adjust [%]
BPM
Base Note x Times
Adjust [%]
MIDI,
BPM
40.00...
300.00
a
Time Over? L
---, OVER!
R
---, OVER!
L Delay Base
r...w
Note
b
Times
x1...x32
Adjust [%]
–2.50...+2.50
R Delay Base
r...w
Note
c
Times
x1...x32
Adjust [%]
–2.50...+2.50
L Feedback
–100...+100
d
Src
Off...Tempo
Amt L
–100...+100
R Feedback
–100...+100
e
Amt R
–100...+100
f
High Damp [%] 0...100
g Low Damp [%] 0...100
Input Level
–100...+100
Dmod [%]
h
Src
Off...Tempo
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
a: Time Over? L, R
You can set the delay time up to 2,730msec. If the delay time
exceeds this limit, the error message "OVER!" appears in the dis-
play. Set the delay time parameters so that this message will not
appear. "Time Over?" is only a display parameter.
FX Amt
High Damp Low Damp
Delay
Feedback
High Damp Low Damp
Delay
FX Amt
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Display the error message if the left
channel delay time exceeds the
upper limit
Display the error message if the
right channel delay time exceeds
the upper limit
Selects the type of notes to specify
the left channel delay time
Sets the number of notes to specify
the left channel delay time
Fine-adjust the left channel delay
time
Selects the type of notes to specify
the right channel delay time
Sets the number of notes to specify
the right channel delay time
Fine-adjust the right channel delay
time
Sets the feedback amount for the
left channel
Selects the modulation source of
feedback amount
Sets the modulation amount of the
left channel feedback
Sets the feedback amount for the
right channel
Sets the modulation amount of the
right channel feedback
Sets the damping amount in the
high range
Sets the damping amount in the low
range
Sets the modulation amount of the
input level
Selects the modulation source for
the input level
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source
Advertisement
Table of Contents
