Korg Pa300 User Manual page 342

338 Effects
Mono-Mono Serial (Mono-Mono)
97: Exciter - Phaser
This effect combines a mono limiter and a phaser.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Exciter
EQ Trim HEQ
LEQ
+
Exciter
Right
EXCITER
[X]Exciter
a –100...+100
Blend
[X]Emphasis
b 0...70
Frequency
c [X]Trim 0...100
[X]Pre LEQ
–15...+15
Gain [dB]
d
Pre HEQ Gain
–15...+15
[dB]
PHASER
[P]LFO
Frequency [Hz] 0.02...20.00
e
LFO Waveform Triangle, Sine
[P]Manual 0...100
f Depth 0...100 Sets the depth of LFO modulation
Resonance –100...+100
-Wet, -
[P]Phaser Wet/
1:99...Dry...99:1,
Dry
Wet
g
Src Off...Tempo
Amt –100...+100
[P]Output Normal,
h
Mode Wet Invert
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src Off...Tempo
Amt –100...+100
FX Amt
Phaser
Phaser
Normal
+
Output Mode
–
Wet Invert
Resonance
Phaser FX Amt
FX Amt
LFO: Tri / Sine
Sets the intensity (depth) of the
Exciter effect
Sets the frequency range to be
emphasized
Sets the EQ input level
Sets the gain of Low EQ
Sets the gain of High EQ
Sets the speed of the LFO
Selects the LFO Waveform
Sets the frequency to which the
effect is applied
Sets the resonance amount
Sets the phaser effect balance
Selects the Wet/Dry modulation
source for the phaser
Sets the Wet/Dry modulation
amount for the phaser
Selects the phaser output mode
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source
98: Exciter - Mt.Delay
(Exciter - Multitap Delay)
This effect combines a mono exciter and a multitap delay.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
Exciter
EQ Trim LEQ HEQ
+
Exciter
Right
EXCITER
[X]Exciter
a –100...+100
Blend
[X]Emphasis
b 0...70
Frequency
c [X]Trim 0...100
[X]Pre LEQ
–15...+15
Gain [dB]
d
Pre HEQ Gain
–15...+15
[dB]
MULTITAP DELAY
[D]Tap1 Time
0.0...1360.0
[msec]
e
Tap1 Level 0...100
[D]Tap2 Time
0.0...1360.0
[msec]
f
Feedback
–100...+100
(Tap2)
[D]High Damp
g 0...100
[%]
[D]Mt.Delay Dry, 1:99...99:1,
Wet/Dry Wet
h Src Off...Tempo
Amt –100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src Off...Tempo
Amt –100...+100
FX Amt
Multitap Delay
Feedback
Delay
(2)
(1)
High Damp
Mt.Dly FX Amt
FX Amt
Sets the intensity (depth) of the
Exciter effect
Sets the frequency range to be
emphasized
Sets the EQ input level
Sets the gain of Low EQ
Sets the gain of High EQ
Sets the Tap1 delay time
Sets the Tap1 output level
Sets the Tap2 delay time
Sets the Tap2 feedback amount
Sets the damping amount in the
high range
Sets the multitap delay effect
balance
Selects the Wet/Dry modulation
source for the multitap delay
Sets the Wet/Dry modulation
amount for the multitap delay
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source