Download Print this page

Advertisement

308
Effects
Modulation and Pitch Shift (Mod./P.Shift)
42: Doppler
This effect simulates the "Doppler effect" of a moving sound
with a changing pitch, similar to the siren of an passing ambu-
lance. Mixing the effect sound with the dry sound will create a
unique chorus effect.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
+
Doppler
Right
LFO
D
-mod
Trigger
LFO Mode = 1-Shot
LFO Mode
Loop, 1-Shot
a
Src
Off...Tempo
b LFO Sync
Off, On
LFO Frequency
0.02...20.00
[Hz]
c
Src
Off...Tempo
–20.00...
Amt
+20.00
MIDI Sync
Off, On
MIDI,
BPM
40.00...
d
300.00
Base Note
r...w
Times
x1...x32
Pitch Depth
0...100
e
Src
Off...Tempo
Amt
–100...+100
Pan Depth
–100...+100
f
Src
Off...Tempo
Amt
–100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
g
Src
Off...Tempo
Amt
–100...+100
a: LFO Mode
a: Src
b: LFO Sync
The "LFO Mode" parameter switches LFO operation mode.
When Loop is selected, the Doppler effect will be created repeat-
edly. If "LFO Sync" is set to On, the LFO will be reset when the
modulation source specified with the "Src" parameter is turned
on.
When "LFO Mode" is set to 1-Shot, the Doppler effect is created
only once when the modulation source specified in the "Src"
field is turned on. At this time if you do not set the "Src" param-
eter, the Doppler effect will not be created, and no effect sound
will be output.
FX Amt
Pan Depth
FX Amt
Switches LFO operation mode
Selects the modulation source of
LFO reset
Switches between LFO reset on and
off when LFO Mode is set to Loop
Sets the speed of the LFO
Selects a modulation source for LFO
speed
Sets the modulation amount of LFO
speed
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the type of notes that
specify the LFO speed
Sets the number of notes that
specify the LFO speed
Sets the pitch variation of the
moving sound
Selects the modulation source of
pitch variation
Sets the modulation amount of
pitch variation
Sets the panning of the moving
sound
Selects the modulation source of
panning
Sets the modulation amount of
panning
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source
The effect is off when a value for the modulation source specified for
the "Src" parameter is smaller than 64, and the effect is on when the
value is 64 or higher. The Doppler effect is triggered when the value
changes from 63 or smaller to 64 or higher.
e: Pitch Depth
With the Doppler effect, the pitch is raised when the sound
approaches, and the pitch is lowered when the sound goes away.
This parameter sets this pitch variation.
f: Pan Depth
This parameter sets the width of the stereo image of the effect
sound. With larger values, the sound seems to come and go from
much further away. With positive values, the sound moves from
left to right; with negative values, the sound moves from right to
left.
Pitch
Pan Depth
= (+) value
Original Pitch
Left
<
<
<
< < <<<<<< >>>>>> > >
Louder
43: Scratch
This effect is applied by recording the input signal and moving
the modulation source. It simulates the sound of scratches you
can make using a turntable.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
+
Rec Control
Right
D-mod
D
-mod
Envelope Control
Input
Envelope Select
D
a
Scratch Source Off...Tempo
b Response
0...100
Envelope
D-mod, Input
Select
c
Src
Off...Tempo
d Threshold
0...100
e
Response
0...100
Always On,
f
Direct Mix
Always Off,
Cross Fade
Dry, 1:99...99:1,
Wet/Dry
Wet
g
Src
Off...Tempo
Amt
–100...+100
Doppler - Pitch / Pan Depth
Pan Depth
= (–) value
Pitch Depth
Center
Right
Pan Depth
>
>
>
Volume
Louder
FX Amt
Direct
Scratch
Mix
Scratch
FX Amt
-mod
Selects the modulation source for
simulation control
Sets the speed of the response to
the Scratch Src
Selects whether the start and end of
recording is controlled via the
modulation source or the input
signal level
Selects the modulation source that
controls recording when Envelope
Select is set to D-mod
Sets the recording start level when
Envelope Select is set to Input
Sets the speed of the response to
the end of recording
Selects how a dry sound is mixed
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source

Advertisement

   Also See for Korg Pa300

   Related Manuals for Korg Pa300

Comments to this Manuals

Symbols: 0
Latest comments: