Download Print this page

Advertisement

300
Effects
Chorus, Flanger, and Phaser (Cho/Fln Phaser)
28: St.HarmonicChorus
(Stereo Harmonic Chorus)
This effect applies chorus only to higher frequencies. This can be
used to apply a chorus effect to a bass sound without making the
sound thinner. You can also use this chorus block with feedback
as a flanger.
Stereo In - Stereo Out
Left
Chorus/Flanger
High/Low Split Point
Chorus/Flanger
Right
LFO Phase
LFO: Tri / Sine
LFO Waveform Triangle, Sine
a
LFO Phase
–180...+180
[degree]
LFO Frequency
0.02...20.00
[Hz]
b
Src
Off...Tempo
–20.00...
Amt
+20.00
MIDI Sync
Off, On
MIDI,
BPM
40.00...
c
300.00
Base Note
r...w
Times
x1...x32
Pre Delay
d
0.0...50.0
[msec]
Depth
0...100
Src
Off...Tempo
e
Amt
–100...+100
High/Low Split
f
1...100
Point
Feedback
–100...+100
g
High Damp [%] 0...100
Low Level
0...100
h
High Level
0...100
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
f: High/Low Split Point
This parameter sets the frequency that splits the high and low
range. Only the high range will be sent to the chorus block.
g: Feedback
Sets the feedback amount of the chorus block. Increasing the
feedback will allow you to use the effect as a flanger.
Low Level
FX Amt
High Level
High Damp
Feedback
High Damp
High Level
Low Level
FX Amt
Selects the LFO Waveform
Sets the LFO phase difference
between the left and right
Sets the speed of the LFO
Selects a modulation source for LFO
speed
Sets the modulation amount of LFO
speed
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the type of notes that
specify the LFO speed
Sets the number of notes that
specify the LFO speed
Sets the delay time from the original
sound
Sets the depth of LFO modulation
Selects the modulation source of
the LFO modulation depth
Sets the modulation amount of the
LFO modulation depth
Sets the frequency split point
between the low and high range
Sets the feed back amount of the
chorus block
Sets the high range damping
amount of the chorus block
Sets the low range output level
Sets the high range (chorus) output
level
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source
29: St. Biphase Mod.
(Stereo Biphase Modulation)
This stereo chorus effect adds two different LFOs together. You
can set the Frequency and Depth parameters for each LFO indi-
vidually. Depending on the setting of these LFOs, very complex
waveforms will create an analog-type, unstable modulated
sound.
Stereo In - Stereo Out
Left
Chorus/Flanger
Chorus/Flanger
Right
180 [degree]
LFO1: Tri / Sine
LFO2: Tri / Sine
LFO1
Triangle, Sine
Waveform
a
LFO2
Triangle, Sine
0 deg,
Phase Sw
180 deg
LFO1
0.02...30.00
Frequency [Hz]
b
Src
Off...Tempo
–30.00...
LFO1 Amt
+30.00
LFO2
0.02...30.00
Frequency [Hz]
c
–30.00...
Amt
+30.00
Depth1
0...100
d
Src
Off...Tempo
Amt
–100...+100
Depth2
0...100
e
Amt
–100...+100
L Pre Delay
0.0...50.0
[msec]
f
R Pre Delay
0.0...50.0
[msec]
Feedback
–100...+100
g
High Damp
0...100
[%]
-Wet, -
Wet/Dry
1:99...Dry...99:1
, Wet
h
Src
Off...Tempo
Amt
–100...+100
LFO1
Depth1
LFO2
Depth2
FX Amt
High Damp
Feedback
High Damp
FX Amt
Selects LFO1 waveform
Selects LFO2 waveform
Switches the LFO phase difference
between left and right
Sets the LFO1 speed
Selects the modulation source of
LFO1&2 speed
Sets the modulation amount of
LFO1 speed
Sets the LFO2 speed
Sets the modulation amount of
LFO2 speed
Sets the depth of LFO1
modulation
Selects the modulation source of
LFO1&2 modulation depth
Sets the modulation amount of
LFO1 modulation depth
Sets the depth of LFO2
modulation
Sets the modulation amount of
LFO2 modulation depth
Sets the delay time for the left
channel
Sets the delay time for the right
channel
Sets the feedback amount
Sets the damping amount in the
high range
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 283
Amount of modulation source
Bi-Phase Modulation LFO
+

Advertisement

   Also See for Korg Pa300

Comments to this Manuals

Symbols: 0
Latest comments: