Table of Contents
Advertisement
OPERATING
APPLIANCE
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING:
.
If you do not
follow these instructions exactly, a
fire
or
explosion
causing property damage, personal
injury or loss of life.
BEFORE LIGHTING smell all around the
appliance area for gas. Be sure to smell
next to the floor because some gas is
heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
¡ ñ
Do not try to light any appliance.
¡ ñ
Do not touch any electric switches; do
not use any phone in your building.
¡ ñ Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
¡ ñ
If you cannot reach your gas supplier,
call the fire department.
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information
above.
2. Turn the gas shutoff valve to OFF.
3. Wait five (5) minutes to clear out any gas.
If you still smell gas, STOP! Follow the
safety information above. If you don't
smell gas, go on to the next step.
4. Light a match and lay it on top of the pan
material about 2" from the end of the
supply side of the pan.
5. Slowly turn the gas shutoff valve ON
until the burner ignites. If the burner
doesn't ignite within 10 seconds with the
match burning, turn the shutoff valve
OFF and repeat steps 1 through 4 again.
PRO-COM OWNER'S MANUAL
VENTED GAS LOGS
Flame Adjustment
Adjust the flame ON/OFF by
turning the gas shutoff valve
may
result
counter-clockwise
open or clock-wise
close, as necessary.
Shutting Off Appliance
Turn gas shutoff valve clockwise
During the 2-3 hour appliance break-in
period, you may detect an odor from the
appliance as the various paints and
compounds used in the manufacturing of
this log set cure. This is a normal and
temporary situation that is not cause for
alarm. However, you may want to provide
extra ventilation to the room during this
time.
To ensure proper curing of the logs:
¡ ñ
Ignite a 2" flame and maintain it for 1
hour.
¡ ñ
Burn the logs in consecutive 1 hour
periods raising the flame an additional
2" to full flame height for a total of
three hours.
TECHNICAL SERVICE
You may have further questions about
installation,
troubleshooting.
PRO-COM's 800# on the back of this
manual.
CLEANING AND
MAINTENANCE
●
●
●
GAS SHUTOFF
VALVE OPERATION
to the OFF position.
CURING LOGS
operation,
If
so,
Keep the area around the log set
clean and clear of debris.
Occasionally, you may use a soft
bristle brush to clean logs.
Once every year a qualified agency
or certified chimney sweep should
examine and clean the venting
system of the fireplace.
6
REPLACEMENT PARTS
Note: Use only original replacement
parts. This will protect your warranty
coverage for parts replaced under
warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this
product. If they can't supply original
replacement part(s), call the number
on back of manual. When calling
to
PRO-COM, have ready
to
¡ ñ your name
¡ ñ your address
¡ ñ model and serial numbers of your
fireplace
¡ ñ
how fireplace was malfunctioning
¡ ñ
type of gas used (propane/LP or
natural gas)
¡ ñ purchase date
Usually, we will ask you to return the
defective part to the factory
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this
product. If they can't supply original
replacement part(s), call PRO-COM's
800# on the back of this manual.
ACCESSORIES
Purchase these fireplace accessories
from your local dealer. If they can not
supply
these
PRO-COM's 800# for information. You
can also write to the address listed on
the back page of this manual.
or
contact
EQUIPMENT SHUTOFF VALVE
For all models. Equipment shutoff
valve with 1/8" NPT tap. Fits 1/2"
NPT pipe. This part is not currently
available from PRO-COM.
SAFETY VALVE/PILOT KIT
Model: NVDWA1
For
all
models.
propane/LP installation.
accessories,
call
Required
for
WAL21-01
Advertisement
Table of Contents
