Chevrolet 1977 light duty truck Service Manual page 187

F R O N T E N D
Windshield Wiper Linkage to Plenum ........................ 25 in. lb.
Sunshade S u p p o r t .......................................................... 20 in. lb.
Inside Rear View Mirror to Bracket............................. 45 in. lb.
Outside Rear View Mirror to Door Panel —
Base M i r r o r ............................................................. 25 in. lb.
West Coast Mirror— Lower Bracket to Door . . . 20 in. lb.
— Upper Bracket to Door. . . . 45 in. lb.
D O O R S
Window Regulator Assembly to Door P a n e l ............. 85 in. lb.
Remote Control Door Lock to Door P a n e l ................45 in. lb.
Lock Striker to Body P ill a r ........................................... 45 ft. lb.
Outside Door Handle........................................................85 in. lb.
Inside Door H a n d l e ........................................................85 in. lb.
Hinges to Body and D o o r ............................................. 35 ft. lb.
Front Door-Window Run Channel
Upper Screw Assembly ........................................85 in. lb.
Lower Bolt Assembly. . ........................................ 18 in. lb.
Front Door-Ventilator Assembly
Top Vent S c r e w ..................................................... 18 in. lb.
Side Vent Screws and S p a c e rs............................. 25 in. lb.
Lower Vent Channel B o l t s .................................. 40 in. lb.
Side Rear Door— Run Channel
Front Upper to D o o r ............................................. 40 in. lb.
Rear Upper to Door ............................................. 20 in. lb.
Front and Rear Lower to Door............................. 85 in. lb.
Lock Lever to Door ............................................. 85 in. lb.
Rear Door—Lock Striker (06) ..................................... 95 in. lb.
Rear Door— Latch L.H. and R.H. to Door (06) . . . . 85 in. lb.
Rear Door— Latch Control Assembly to Door (06)
— Upper A sse m b ly ........................................85 in. lb.
— Lower A ssem bly........................................90 in. lb.
Rear Door— Weatherstrip L.H. ( 0 6 ) ............................. 18 in. lb.
E N D G A T E (1 4 )
Hinges— Body Half and Gate H a l f ................................35 ft. lb.
Support Assembly-Body to End G a t e ........................25 ft. lb.
Torque Rod-Retainer Assembly.................................. 85 in. lb.
— Anchor A sse m b ly .................................. 18 ft. lb.
Latch Assembly to End G a t e ........................................85 in. lb.
la tc h Control Assembly to End Gate ........................ 40 in. lb.
Access Cover..................................................................... 18 in. lb.
Handle to Latch Control A ssem bly............................. 55 in. lb.
Glass Channel Assembly to End Gate ........................85 in. lb.
Cap Assembly to Channel Assembly............................. 24 in. lb.
Striker— Body Mounted ................................................18 ft. lb.
SPECIFICATIONS
BODY
SECTION 2D
C AND K MODELS
Hinges— Hinge to B o d y .................................................. 35 ft. lb.
— Hinge to End Gate.............................................20 ft. lb.
Support Cable B o lts ....................................................... 25 ft. lb.
Torque Rod-Silencer Bracket..................................... 40 in. lb.
Latch Assembly to End G a t e ........................................20 ft. lb.
Latch Remote Control Assembly to End Gate
Access Cover .................................................................. 18 in. lb.
Outside Handle
Glass C hannel.................................................................. 45 in. lb.
T A I L G A T E (03, 6 3 - w i t h E63)
Trunnion A ssem b ly ........................................................18 ft. lb.
Linkage and Striker Assembly— Support
T A I L G A T E (03, 6 3 - w i t h E62)
Trunnion A sse m b ly ....................................................... 35 ft. lb.
Chain Support Assembly .............................................90 in. lb.
Front Bench Seat
Adjuster-to-Seat
Adjuster-to-Floor.................................................. 25 ft. lb.
Front Bucket Type (14, 03)
Driver
Adjuster-to-Seat.............................................18 ft. lb.
Adjuster-to-Floor
Passenger (03)
Support-to-Seat.............................................18 ft. lb.
Support-to-Floor (F r o n t) .............................25 ft. lb.
Support-to-Floor ( R e a r ) ............................. 40 ft. lb.
Passenger (14)
Latch Support-to-Seat (Rear)
Striker-to-Floor (Rear)
Support (Upper)-to-Seat (Front)
Support (Lower)-to-Floor ( F r o n t ) ............. 25 ft. lb.
Support (Upper)-to-Support (Lower) . . . . 30 ft. lb.
Rear Bench (06, 14)
Support-to-Seat.....................................................18 ft. lb.
Support-to-Floor .................................................. 50 ft. lb.
Rear Bench (63)
Support-to-Seat.................................................. 150 In. lb.
Support-to-Floor .................................................. 35 in. lb.
Folding Rear Seat (06)
Support Asm-to-Floor....................................... 150 in. lb.
Seat-to-Support A s m .............................................18 in. lb.
E N D G A T E (0 6 )
— End Support Bracket............................. 90 in. lb.
.............................................................55 in. lb.
.................. 25 in. lb.
S E A T S
................................................155 in. lb.
....................................... 25 ft. lb.
.............................25 ft. lb.
. . . . 40 in. lb.
...................18 ft. lb.
............. 18 ft. lb.