Table of Contents
Advertisement
Camera Function Control
Camera Setup
The following function requires the use of cameras
equipped with this specific feature.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Pressing the [STOP] button while holding down the
[SHIFT] button will open the Camera Setup Menu on
the active monitor.
The STOP indicator will light.
ALARM
ACK
DISARM
GROUP PRESET
PREV
OPE ID
S-CTL ID
LOG OUT
PAUSE
CAM MENU OFF
GROUP
F1
SEQ
F2
OSD
CAM FUNC
3. Select the desired item in the menu by moving the
Joystick Controller UP and DOWN, and then select the
desired parameter (or mode) in the menu by moving
the Joystick Controller L and R.
Press the [CAMERA (ENTER)] button to execute the
currently highlighted selection and to enter a submenu
of the Camera Setup Menu, or press the [CLEAR
(ESC)] button to leave from the currently selected
menu and return to the previous page of the menu.
4. Press the [RESET] button in the menu to reset the
parameter of a selected item to the factory default set-
ting or enter the Special Camera Menu when the cursor
is positioned on SPECIAL in the menu.
Pressing the [RESET] button while holding down the
[SHIFT] button will restore all factory default settings.
Notes:
• Refer to the Operating Instructions of the selected
camera for more details.
• Moving the joystick while holding down the [SHIFT]
button will move the camera smoothlyfor presetting
the position in the camera setup menu.
5. To close the Camera Setup Menu, press the [PAUSE]
button while holding down the [SHIFT] button.
The STOP indicator will go off.
107
RESET
ALL RESET
NEXT
T&D
CAM ID
GEN
AUX1 OFF
AUX1 ON
WIPER
ALM S
VLD S
SYS S
STOP
MON STATUS
ALL
CAM MENU ON
AUX2 OFF
AUX2 ON
TOUR
ALM H
VDL H
SEQ
DEF OFF
DEF ON
CLEAR
MONITOR
( ESC )
LOCK
SHIFT
BLK
EXIT
OSD SERVICE
Camera Function (Shortcut
Function)
The following function is available only when specified cam-
eras with the camera function feature are used.
This function enables executing camera functions via a
shortcut.
1. Select the desired monitor and camera.
Refer to the Monitor Selection and Camera Selection.
2. Press the [F2] button.
"F----" as shown in the figure will appear on the LED
display of the controller.
PROGRAM
PRESET
ALARM
CALL
PRESET
DISARM
GROUP PRESET
CAMERA
OPE ID
S-CTL ID
( ENTER )
LOG OUT
AUTO
PAN
CAM MENU OFF
F1
F2
CAM FUNC
3. Select an assigned function number by pressing the
numeric buttons, then press the [CAMERA (ENTER)]
button.
For example, enter 175 for AGC On.
The selected function will be executed on the active
monitor.
Note: For further information, refer to the Operating
Instructions for that camera.
4. To exit from the mode, press the [CLEAR (ESC)] but-
ton.
ACK
RESET
ALL RESET
PREV
NEXT
T&D
CAM ID
AUX1 OFF
AUX1 ON
ALM S
VLD S
PAUSE
STOP
MON STATUS
CAM MENU ON
AUX2 OFF
AUX2 ON
GROUP
TOUR
ALM H
VDL H
SEQ
SEQ
DEF OFF
DEF ON
OSD
MONITOR
LOCK
SHIFT
BLK
OSD SERVICE
PROGRAM
PRESET
GEN
WIPER
SYS S
ALL
CALL
PRESET
CLEAR
CAMERA
( ESC )
( ENTER )
EXIT
AUTO
PAN
Advertisement
Table of Contents
