Table of Contents
Advertisement
@1 Alarm Reset button (RESET)
Cancels an activated alarm.
Press this button to reset an alarm activated in the cur-
rently active unit.
Pressing this button while holding down the SHIFT but-
ton cancels all currently activated alarms at a time (ALL
RESET).
Pressing RESET in the Camera Menu will reset the
parameter of a selected item or open the Special
Camera Menu when the cursor is positioned on SPE-
CIAL in the menu. Pressing it while holding down the
SHIFT button will restore all factory default settings.
@2 Next button (NEXT)
This button is used to move a Tour Sequence one step
forward from the step that was previously paused on
the active monitor by pressing the PAUSE button.
The button is also used to select a camera. Pressing
NEXT while holding down the CAMERA (ENTER) button
will replace the currently selected camera with the next
higher camera number, if the active monitor is in Spot
mode.
Similarly pressing NEXT while holding down the MONI-
TOR button will select the next higher monitor number.
When selecting alarms, pressing NEXT while holding
down the ALARM button will select the next alarm.
@3 Previous button (PREV)
This button is used to move a Tour Sequence one step
backward from the step that was previously paused on
the active monitor by pressing the PAUSE button.
This button is also used to select a camera. Pressing
PREV while holding down the CAMERA (ENTER) button
will replace the currently selected camera with the next
lower camera number, if the active monitor is in Spot
mode.
Similarly pressing PREV while holding down the MONI-
TOR button will select the next lower monitor number.
When selecting alarms, pressing PREV while holding
down the ALARM button will select the previous alarm.
Pressing this button while holding down the SHIFT but-
ton will display the Controller ID number on the LED
Display for about 3 seconds (S-CTL ID).
@4 Stop button (STOP)
This button is used to end a Tour Sequence that is
being run on the active monitor.
To end a Group sequence, select one of the monitors
that are being run on the selected sequence, then
press this button.
Pressing STOP while holding down the SHIFT button
will open the Camera Menu on the active monitor. The
STOP indicator will light. (CAM MENU ON)
@5 Pause button (PAUSE)
This button is used to pause a Tour or Group Sequence
that is being run on the active monitor.
Pressing PAUSE while holding down the SHIFT button
will close the Camera Menu on the active monitor. The
STOP indicator will go off. (CAM MENU OFF)
54
@6 Tour Sequence button (TOUR SEQ)
This button, in combination with the Numeric buttons, is
used to run a Tour Sequence on the active monitor.
Pressing TOUR SEQ will restart a forward sequence
from the next step that was previously paused by
pressing the PAUSE button.
@7 Group Sequence button (GROUP SEQ)
This button, in combination with the Numeric buttons, is
used to run a Group Sequence on the assigned moni-
tors.
Pressing GROUP SEQ will restart a forward sequence
from the next step that was previously paused by
pressing the PAUSE button.
@8 Group Preset button (GROUP PRESET)
This button, in combination with the Numeric buttons, is
used to activate a previously programmed Group
Preset function.
Pressing This button while holding down the SHIFT but-
ton will display the Operator ID number on the LED
Display for about 3 seconds (OPE ID).
@9 Log Out button (LOGOUT)
This button, in combination with the CAMERA (ENTER)
button, is used to log out from the system.
To prevent a log-out error, press CAMERA (ENTER)
while holding down the LOGOUT button.
#0 Function buttons (F1, F2)
These buttons provide access to camera attributes and
operating functions.
F1: Reserved for future use.
F2: Pressing this button will select the mode for control-
ling selected camera function (CAM FUNC).
#1 OSD (On-Screen Display) button (OSD)
This button is used to toggle the currently selected dis-
play on and off on the active monitor.
Pressing the numeric buttons shown below while hold-
ing down the OSD button will toggle the following dis-
play items on the active monitor on and off.
1: Clock Display (T&D)
2: Camera Title Display (CAM ID)
3: General Status Display (GEN)
5: Monitor Status Display (MON STATUS)
6: All Displays except clock (ALL)
#2 Monitor button (MONITOR)
This button is used to select a monitor.
To select a monitor, press the corresponding Numeric
buttons, followed by the MONITOR button.
Pressing this button while holding down the SHIFT but-
ton will toggle the indicator on and off. The indicator
lights to indicate that the currently selected monitor is
priority locked, and retains control of a monitor by an
operator.
This button, in combination with the Numeric buttons, is
also used to display the status and history tables on the
active monitor screen.
Advertisement
Table of Contents
