Cd80 series infrared turret dome ccd camera (20 pages)
Summary of Contents for Observint Black BLK-HDC10
Page 1
BLK-HDC10 2-Megapixel Full-HD C-mount Box Camera User Manual Please read this manual before using your camera, and always follow the instructions for safety and proper use. Save this manual for future reference. BLK-HDC10_CM...
Page 2
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Observint disclaims any proprietary interest in trademarks and trade names other than its own.
PRECAUTIONS WARNING - Do not install this equipment in a confined space such as a bookcase or similar unit. WARNING - Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70. WARNING - This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions - All these safety and operating instructions should be read before the product is operated. Keep these instructions - The safety, operating and user instructions should be retained for future reference. Heed all warnings - All warnings on the product and in the operating instructions should be adhered to.
SECTION 1: INTRODUCTION SECTION 1 Introduction This high definition indoor C/CS mount camera features 2.1 megapixel imaging with 1920 x 1080 resolution along with 3-dimensional Noise Reduction (3D-NR). A lens is not included. 3D-NR automatically provides a more accurate noise reduction. This is based on twice the visual information than conventional field-based types.
Page 8
Lens iris output connector: 4-pin connector used to send the Iris control signal and power supply to an auto-iris type lens • DC -type lenses Damping - Damping + Drive + Drive - 1.1.1 Camera back panel Power indicator External device HD-SDI connector connections Video out connector Power input terminals BLK-HDC10 back connectors...
SECTION 1: INTRODUCTION NOTES: Power indicator - LED lights when the power is applied to the camera. • External Device Connectors: • D&N - To set the D&N (day and night) function manually, connect the external switch to set the D&N terminals. Open —...
SECTION 2: INSTALLATION SECTION 2 Installation 2.1 Camera installation bracket setup The camera can be attached to a mounting bracket on the upper side or the underside of the camera. Normally, the bracket is factory installed on the underside of the camera. If the camera will attach to the mounting bracket on the upper side, remove the bracket from the underside of the camera and reattach it to the upper side.
SECTION 2: INSTALLATION 2.2 Attach the lens The camera will accommodate a C- or CS-type lens. To attach the lens, do the following: Remove the lens mounting cap from the lens mounting ring as shown below. Lens mounting ring Carefully screw the lens assembly clockwise onto the lens mounting ring until it is fully seated. Tighten until snug. Lens mounting ring If you installed an auto-iris lens, verify that the cable pin definitions match the lens output iris connector (see “1.1 Camera components”...
Page 12
SECTION 2: INSTALLATION Follow the manufacturer’s instructions to attach the camera mounting bracket to the mounting surface. Attach the camera to camera mounting bracket. Attach the RS-485, alarm output device, and D&N switch to the terminal block on the back of the camera, as needed. See “1.1.1 Camera back panel”...
Page 13
SECTION 2: INSTALLATION Connect power leads to the power terminals on the back of the camera in compliance with local codes. Ensure that the leads do not have applied to them when making the connections. Connect the leads in accordance with the terminal polarity on the back of the camera.
SECTION 3: CONFIGURATION SETUP SECTION 3 Configuration Setup Use the on-screen display (OSD) menus to configure your camera for the environment where it is installed and recording requirements you prefer. 3.1 Menu operation Navigation through the menu system is performed menu navigation buttons located under the camera side panel. Up button p: Moves the cursor upwards in the menu.
SECTION 3: CONFIGURATION SETUP 3.2 CAMERA MODE CAMERA MODE: Select mode type: D&N (day and night) / COLOR / IR SMART / IR CDS. The mode selected affects the content of some displays. 3.3 EXPOSURE To open the EXPOSURE menu, rock the joystick down (or up) to highlight EXPOSURE, then press the joystick down (set, select). BRIGHTNESS: Adjust brightness level: 0 (dark) ~ 20 (bright) steps •...
SECTION 3: CONFIGURATION SETUP COLOR Model AUTO / DAY / NIGHT / EXT — Delay: 0 ~ 255 second — BURST: OFF / ON — THRS: LOW / MIDDLE / HIGH — GAP: LOW / MIDDLE / HIGH — IR SMART Model (not used with this camera) IR CDS Model AUTO / DAY / NIGHT —...
SECTION 3: CONFIGURATION SETUP MANUAL: You can change WB as changing “RED GAIN” and “BLUE GAIN” in manual mode. — RED GAIN: Adjust R gain value 0 ~ 20 » BLUE GAIN: Adjust B gain value 0 ~ 20 » INDOOR: Set color temperature to be Indoor light (3700 K) —...
SECTION 3: CONFIGURATION SETUP ACE: Select Digital WDR (Wide Dynamic Range): OFF / ON. NOTE: When ACE is On, WDR/BLC and DEFOG function can not turn • WDR Off WDR ON DNR: Select Digital Noise Reduction: AUTO / OFF / LOW / MIDDLE / HIGH •...
SECTION 3: CONFIGURATION SETUP 3.7 SPECIAL FUNCTION SHADING DET: Sets the shading calibration that the lens will perform. Only occurs when the entire screen is viewed in white • light.(OFF / ON) SHADING: Select Lens shading compensation. (OFF / ON) •...
SECTION 3: CONFIGURATION SETUP 3.8 DISPLAY DISP SEL: Select display item. • ID: OFF / ON — TITLE: OFF / ON — EZOOM: OFF / ON — SET TITLE: Select camera title menu (Text edit) • Set Title character set (on-screen)
SECTION 4: SPECIFICATIONS SECTION 4 Specifications Table 1. Component Specifications Component Value Image Sensor 1/3" Panasonic CMOS Total Pixels 2010 (h) x 1108 (v) = 2,227,080 (pixels) Active Pixels 1944 (h) x 1092 (v) = 2,122,848 (pixels) Scanning system Progressive Digital: 1920 x 1080 (1080p / 30 fps), 1280 x 720 (720p / 60 fps) Resolution Analog: 700 TVL...
Page 22
SECTION 4: SPECIFICATIONS Component Value Off / On Off / On Off / Low / Middle / High / Auto D.COMPRESS OFF / ON GAMMA 0.45 – 0.65 INTELLIGENCE PRIVACY Off / On (32 points) SPECIAL FUNC SHADING DET Off / On SHADING Off / On DEFECT DET...
APPENDIX A: TROUBLESHOOTING APPENDIX A Troubleshooting If you experience problems you cannot resolve, please contact your distributor. Problem Solution Nothing appears on the screen. - Check the power connections. - Check the video cable connections. - Ensure that the lens mode is set to DC (VIDEO) when using a VIDEO (DC) lens. The video image is not clear.