Cd80 series infrared turret dome ccd camera (20 pages)
Summary of Contents for Observint Black BLK-HDC10IR
Page 1
BLK-HDC10IR 2 Megapixel Indoor/Outdoor IR Bullet Camera User Manual NOTE: This device operates on 12 Vdc only. Please read this manual before using your camera, and always follow the instructions for safety and proper use. Save this manual for future reference.
Page 2
LEGAL NOTICE Observint Technologies (Observint) products are designed to meet safety and performance standards with the use of specific Observint authorized accessories. Observint disclaims liability associated with the use of non-Observint authorized accessories.
PRECAUTIONS WARNING - Do not install this equipment in a confined space such as a bookcase or similar unit. WARNING - Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70. WARNING - This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions - All these safety and operating instructions should be read before the product is operated. Keep these instructions - The safety, operating and user instructions should be retained for future reference. Heed all warnings - All warnings on the product and in the operating instructions should be adhered to.
SECTION 1: INTRODUCTION SECTION 1 Introduction This high definition indoor/outdoor IR bullet camera features 2.1 megapixel imaging with 1920 x 1080 resolution along with 3-dimensional Noise Reduction (3D-NR). High definition video – HDcctv security cameras deliver true 1080p or 720p HD video, true HDTV-quality video in live and recorded view modes.
SECTION 1: INTRODUCTION 1.1 Camera components Bolt Sun shield Rotation (horizon) adjustment set screw Tilt adjustment Lens set screw IR LED array Pan adjustment set screw Mounting bracket Drop cable channel Setup monitor and controller port Zoom / focus controls Video output 12 Vdc Power...
SECTION 1: INTRODUCTION NOTES: Setup monitor and controller port: Open the cap on the underside of the camera, then insert the mating service monitor • and controller jack into the plug. Focus / zoom controls • To widen the viewing angle, turn the zoom screw to “W”. —...
SECTION 2: INSTALLATION SECTION 2 Installation 2.1 Mounting the camera The camera can be mounted on any surface with sufficient strength to support it. The camera drop cable can be routed either through the drop cable channel in the mounting bracket, or through a hole in the mounting surface covered by the mounting bracket.
Page 11
SECTION 2: INSTALLATION Pan adjustment Tilt adjustment Rotation adjustment (horizon) Aim the camera at the center of the preferred field of view. Rotate the camera body as needed to align the horizon in the image, then tighten the pan, tilt and rotation set screws. Use a blade screwdriver to adjust the camera focus and zoom as needed.
SECTION 3: CONFIGURATION SETUP SECTION 3 Configuration Setup Use the on-screen display (OSD) menus to configure your camera for the environment where it is installed and recording requirements you prefer. 3.1 Menu operation Navigation through the OSD menu system is performed menu navigation buttons located controller. Up button ...
SECTION 3: CONFIGURATION SETUP 3.3 EXPOSURE To open the EXPOSURE menu, rock the joystick down (or up) to highlight EXPOSURE, then press the joystick down (set, select). BRIGHTNESS: Adjust brightness level: 0 (dark) ~ 20 (bright) steps • LENS: DC / MANUAL •...
Page 14
SECTION 3: CONFIGURATION SETUP COLOR Model AUTO / DAY / NIGHT / EXT — Delay : 0 ~ 255 second — BURST : OFF / ON — THRS : LOW / MIDDLE / HIGH — GAP : LOW / MIDDLE / HIGH —...
SECTION 3: CONFIGURATION SETUP 3.4 WHITE BALANCE AWB : Select WHITE BALANCE mode. AUTO / PRESET / MANUAL / INDOOR / OUTDOOR • AUTO : Automatically adjusts color according to the lighting. — PRESET : It is a fixed white balance mode that may be automatically readjusted only by pressing PRESET —...
Page 16
SECTION 3: CONFIGURATION SETUP H Mirror Off H Mirror ON Freeze : Select real or still mode: OFF / ON • E.ZOOM : Select maximum digital zoom magnification: x1 ~ x12, x14, x15, x18, x21, x25, x32 • HLC : Select High Light Compensation. When extremely bright light is projected to the camera masking is used on the portion •...
SECTION 3: CONFIGURATION SETUP 3.6 INTELLIGENCE PRIVACY : Hide an area you want to hide on the screen: OFF / ON • MASK# : Select mask area number (0 ~ 31) — MODE : Set-up masking areas. (OFF / ON) —...
SECTION 3: CONFIGURATION SETUP 3.7 SPECIAL FUNCTION SHADING DET : Sets the shading calibration that the lens will perform. Only occurs when the entire screen is viewed in white • light.(OFF / ON) SHADING : Select Lens shading compensation. (OFF / ON) •...
SECTION 3: CONFIGURATION SETUP 3.8 DISPLAY DISP SEL : Select display item. • ID : OFF / ON — TITLE : OFF / ON — EZOOM : OFF / ON — SET TITLE : Select camera title menu (Text edit) •...
SECTION 4: SPECIFICATIONS SECTION 4 Specifications Table 1. Component Specifications Component Value Image Sensor 1/3" Panasonic CMOS Total Pixels 2010 (h) x 1108 (v) = 2,227,080 (pixels) Active Pixels 1944 (h) x 1092 (v) = 2,122,848 (pixels) Scanning system Progressive Digital : 1920 x 1080 (1080p / 30 fps), 1280 x 720 (720p / 60fps) Resolution Analog : 700 TVL...
Page 21
SECTION 4: SPECIFICATIONS Component Value Off / Low / Middle / High / Auto D.COMPRESS OFF / ON INTELLIGENCE PRIVACY Off / On (32 points) MOTION Off / On (4 points) SPECIAL FUNC SHADING DET Off / On SHADING Off / On DEFECT DET Off / On DEFOG...
APPENDIX A: TROUBLESHOOTING APPENDIX A Troubleshooting If you experience problems you cannot resolve, please contact your distributor. Problem Solution Nothing appears on the screen. - Check the power connections. - Check the video cable connections. The video image is not clear. - Clean the lens with a soft, clean cloth.