Outback Excel 100T Assembly And Operating Instructions Manual page 21

damage and ensure it is securely attached with
worm drive clips or swaged fittings. Ensure no
part of the flexible hose is touching any hot
barbecue parts. If the hose is damaged, it must
be replaced with hose suitable for use with LPG
and meet the national standards for the country
of use. The length of hose shall not exceed
1.5m. N.B. – The date on UK hose is the date of
manufacture, not the expiry date.
H3. Fixing the Regulator to the Gas Bottle
Confirm all barbecue control knobs are in the off
position. Connect the regulator to the gas bottle
according to your regulator and bottle dealer's
instructions.
H4. Leak Testing (To be performed in a well-
ventilated area.)
Confirm all control knobs are in the off position.
Open the gas control valve on the bottle or
regulator. Check for leaks by brushing a solution
of ½ water and ½ soap over all gas system
joints, including all valve connections, hose
connections and regulator connections. NEVER
USE AN OPEN FLAME to test for leaks at
anytime. If bubbles form over any of the joints,
there is a leak. Turn off the gas supply and
retighten all joints. Repeat test. If bubbles form
again, do not use the barbecue. Please contact
your local dealer for assistance. Leak test your
barbecue annually. Check the hose connections
are tight and leak test them each time you
reconnect the gas bottle.
I. Operation
I1. Warning
•
Before proceeding, make certain that you
u n d e r s t a n d t h e
INFORMATION section of this manual.
I2. Preparation Before Cooking
To prevent foods from sticking to the cooking
grill, please use a long handled brush to apply a
light coat of cooking or vegetable oil before each
barbecuing session. (Note: When cooking for
the first time, paint colours may change
slightly as a result. This is normal and
should be expected.)
I3. Lighting the Barbecue
•
Open the barbecue hood.
•
Ensure all knobs are in the off position.
Open the gas control valve on the gas
bottle or regulator.
•
Push and turn the leftmost control knob to
the high position. Press the ignition button
•
•
I4. Manual Lighting Instructions
•
•
•
•
•
•
I M P O R T A N T
I5. Warming Rack
Warming racks are a convenient way to keep
cooked food warm or to warm items such as
bread rolls. Care should be taken to ensure that
any items placed on the warming rack are
cooked through and do not continue to cook and
drip fat or meat juices, which could drip onto the
hood and down the back of the barbecue.
I6. Grill Cooking
The burner heats up the lava rock underneath
the grill, which in turn heats the food on the grill.
The natural food juices produced during cooking
fall onto the hot lava rock below and vaporise.
The subsequent rising smoke bastes the food,
21
rapidly several times until left portion of the
burner is lit. If burner fails to ignite, turn
control knob to the off position and turn gas
off at the bottle or regulator. Wait five
minutes, then repeat the above steps. After
successful lighting of the left side, ignite the
remaining portion of the burner. If the
burner fails to ignite after following above
procedure, turn all the knobs to the off
position. Close the gas valve on the gas
bottle. Wait 5 minutes, then repeat the
above steps. If the barbecue still fails to
light, please refer to the manual ignition
instructions in section below.
After ignition, the burner should be burned
at the high position for 3-5 minutes in order
to preheat the barbecue. This process
should be done before every cooking
session. The hood (where applicable)
should be open during preheating.
After completion of preheating, the burner
should normally be turned down to a lower
position for best cooking results.
Insert lit match through the match-lighting
hole underneath the barbecue.
Push and turn the rightmost control knob
anti-clockwise to the high position.
After the right portion of the burner is lit,
light the remaining portion of the burner.
If burner fails to ignite, contact your local
dealer for assistance.
After ignition, the burner should be burned
at the high position for 3-5 minutes in order
to preheat the barbecue. This process
should be done before every cooking
session. The hood (where applicable)
should be open during preheating.
After completion of preheating, the burner
should normally be turned down to a lower
position for best cooking results.