Table of Contents
Advertisement
Quick Links
Outback® Trooper, Outback® Hunter, and Outback® Ranger Gas Barbecues
Photographs are not to scale.
Specifications subject to change
without prior notice.
•
•
•
•
•
•
•
•
WARNING
FOR YOUR SAFETY
If you smell gas:
1.
Shut off gas to the appliance.
2.
Extinguish any open flame.
3.
Open barbecue lid or hood.
4.
If odour continues, discontinue use and
contact your local dealer.
Gas Barbecues
Assembly and Operating Instructions for
For outdoor use only.
Read instructions before using the appliance. Failure to follow instructions could
result in death, serious bodily injury, and/or property loss.
Warning: accessible parts may be very hot. Keep young children away.
Do not move the appliance during use.
Turn off the gas supply at the gas bottle after use.
Any modification of the appliance, misuse, or failure to follow the instructions may be
dangerous and will invalidate your warranty. This does not affect your statutory rights.
Retain these instructions for future reference.
Leak test your barbecue annually. Check the hose connections are tight and leak test
each time you reconnect the gas bottle.
FOR YOUR SAFETY
1.
Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2.
A gas bottle not connected for use shall not be
stored in the vicinity of this or any other
appliance.
0359
Advertisement
Table of Contents
Related Manuals for Outback OUTBACK TROOPER 359
Summary of Contents for Outback OUTBACK TROOPER 359
- Page 1 Gas Barbecues Assembly and Operating Instructions for Outback® Trooper, Outback® Hunter, and Outback® Ranger Gas Barbecues Photographs are not to scale. Specifications subject to change 0359 without prior notice. • For outdoor use only. • Read instructions before using the appliance. Failure to follow instructions could result in death, serious bodily injury, and/or property loss.
-
Page 2: Parts List
A. Parts List Quantities vary according to model purchased. Specifications subject to change without prior notice. For more details on hardware, please see ‘Hardware Reference Diagram’. Outback® Outback® Outback® CODE PART Trooper Hunter Ranger Hood (Pre-Assembled to Body) Heat Shield Handle Hinge Plate Gasket... -
Page 3: Parts Diagrams
B. Parts Diagrams Quantities vary according to model purchased. Specifications subject to change without prior notice. For more details on hardware, please see hardware pack page. - Page 4 C. Hardware Reference Diagram Specifications subject to change without prior notice.
-
Page 5: Tools Needed For Assembly
D. Assembly TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/crosspoint screwdriver, adjustable spanner or metric spanner set (Photo depicts trolley from the reverse side) Attach the short (C2,C3) and long legs (C4,C5) to the trolley base (C7) using the trolley bolts (D7). - Page 6 Turn the trolley over so that it stands on its side shelves. Slide the axle (C9) through the corresponding holes in the short legs (C2,C3). Place a washer (D11) on each end of the axle. Slide the wheels (C10) over each end of the axle. Secure the wheels into place with the locknuts (D12).
- Page 7 Lay the assembled trolley on its side. Lay the body (B5) on its back and slide into position between the trolley legs. Warning: Care must be taken to ensure hood does not fall open unexpectedly. When positioning the body of the barbecue, ensure the control panel is on the same side as the legs with Velcro fastenings.
- Page 8 Replace the drip tray (B9) by sliding it underneath the barbecue body. Attach the hood handle (A3) to the hood (A1) by inserting the handle bolts (D4) through the handle (A3), handle spacers (D3), heat shield (A2), and through the front wall of the hood (A1). Secure with washers (D2) and nuts (D1).
- Page 9 Remove the plastic wrap from the lava rock basket(s) (B3) and lay them carefully into the body ensuring that they lie level within the body. Lay the cooking grill(s) (B1) and griddle (B2) into place. 2 burner model configuration: Left half—Cooking Grill, Rock Basket; Right half—Cooking Grill, Rock basket 3 burner model configuration: Left —Cooking Grills, Rock Baskets;...
- Page 10 Leak Test Diagram 11a. Connect the gas hose (B11) to the barbecue (Before the Leaking Test). Ensure the mating faces of the connection are clean and not damaged. Do not use any sealing tape, paste, or liquid on the joint. The nut must be tightened with the use of a spanner. Do not use force which may damage the assembly.
-
Page 11: Installation
UK, the consumer MUST seek advice from the E. Important Information local qualified gas supplier as to the suitability of the barbecue and with regards to the correct hose Please read these instructions carefully before and regulator that they should be using. assembly and use. -
Page 12: Operation
level ground next to the barbecue and safely away more than 50% of the cooking area as a solid from any source of heat. Should you need to plate. Full coverage of plates will cause change the gas bottle, confirm that the barbecue is excessive build-up of heat and damage the switched off, and that there are no sources of barbecue. -
Page 13: Care And Maintenance
complete, cooking can begin, taking extra fork is fully into the meat. Slide the other fork care if burners are left in the high position. onto the rod, into the meat, and tighten the thumb screw once in place. For optimal H5. - Page 14 or stored in damp, moist areas. blocked which may result in a fire behind the control panel causing serious damage to your barbecue. If this happens, the gas should be Never douse the barbecue with water when its immediately turned off at the bottle. Burners surfaces are hot.
-
Page 15: Technical Specifications
replace it with fresh sand. Failure to fill with J. Technical Specifications sufficient clean, dry, loose sand may result in a fat fire or excessive flare up. This can severely Heat Injector Gas / damage your barbecue and is not covered by the Burners Approval Input... -
Page 16: Troubleshooting
K. Troubleshooting Problem Possible Cause Solution Burners will not light using the LP gas cylinder is empty Replace with full cylinder ignition system Faulty regulator Have regulator checked or replace Obstructions in burners Clean burners Obstructions in gas jets or gas hose Clean jets and gas hose Electrode wire is loose or disconnected on Reconnect wire...