Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Silicon Graphics UV 20
Summary of Contents for Silicon Graphics UV 20
- Page 1 ® UV™ 20 System User Guide 007-5900-001...
- Page 2 Contractor/manufacturer is SGI, 46600 Landing Parkway, Fremont, CA 94538. TRADEMARKS AND ATTRIBUTIONS Silicon Graphics, SGI, and the SGI logo, and SGI UV are trademarks or registered trademarks of Silicon Graphics International Corp. in the United States and/or other countries worldwide.
-
Page 3: Record Of Revision
Record of Revision Version Description February 2013 Original printing. 007-5900-001... -
Page 5: Table Of Contents
Contents Record of Revision . . iii About This Guide . . xi System Overview . System Features and Configuration Options Server Components . Hard Disk Drive (HDD) Bays and Front Panel . Control Panel Back Panel . I/O Devices . Hard Disk Drives . - Page 6 Contents Removing the Front Fan Bezel . . 23 Installing the Front Fan Bezel . . 24 Removing the Rack Handles . . 25 Installing the Rack Handles . . 26 Removing the System Top Cover . 27 Replacing the System Cover . .
- Page 7 Figures Figure 1-1 SGI UV 20 Server Figure 1-2 Overhead View of Server with the Top Cover Removed Figure 1-3 Hard Disk Drive Bays Figure 1-4 Front Control Panel . Figure 1-5 Back Panel Figure 1-6 Front Panel I/O Connections .
- Page 8 Figures Figure 4-18 Attaching Slides to the Rack . . 40 Figure 4-19 Installing the Inner Members to the Chassis . . 41 Figure 4-20 Installing the Chassis in the Rack . . 41 Figure 4-21 Extending Slides to Remove the Chassis . .
- Page 9 Tables Tables Table 1-1 Features and Configuration Options . Table 1-2 Control Panel Buttons and LEDs. Table 1-3 Back Panel Components . Table 1-4 I/O Connections . Table 3-1 Control Panel Components and Functions . . 16 Table 3-2 HDD Status LED Functions . .
-
Page 11: About This Guide
Audience This guide is written for owners, installers, system administrators, and users of the UV 20 server. It is written with the assumption that the reader has a good working knowledge of computers and computer systems. -
Page 12: Related Publications
SGI InfiniteStorage series documentation • Man pages (online) You can obtain SGI documentation (as well as the pertinent LSI books), release notes, or man pages in the following ways: • Refer to the SGI Technical Publications Library at http://docs.sgi.com. Various formats are available. -
Page 13: Product Support
If you are in North America, contact the Technical Assistance Center at +1 800 800 4SGI or contact your authorized service provider. • If you are outside North America, contact the SGI subsidiary or authorized distributor in your country. 007-5900-001... - Page 14 If you have comments about the technical accuracy, content, or organization of this document, contact SGI. Be sure to include the title and document number of the manual with your comments. (Online, the document number is located in the front matter of the manual. In printed manuals, the document number is located at the bottom of each page.)
-
Page 15: System Overview
Chapter 1 System Overview The SGI UV 20 server is a 2U rackmount server (see Figure 1-1) It has two main subsystems: the 2U server chassis and a quad-processor serverboard. Figure 1-1 SGI UV 20 Server This chapter describes the main features and configuration options of the server as well as the components pertinent to monitoring and maintaining your server. -
Page 16: System Features And Configuration Options
1: System Overview System Features and Configuration Options Table 1-1 summarizes the features and configuration options of the SGI UV 20 server. Table 1-1 Features and Configuration Options Feature Description Dimensions – Height: 3.43 inches (87.3 mm) – Width: 17.24 inches (438.0 mm) –... - Page 17 System Features and Configuration Options Table 1-1 Features and Configuration Options (continued) Feature Description Riser Cards Support for two riser card slots. Each riser card slot supports three PCIe Gen 3 x16 slots. Video – Integrated 2D video controller – 16 MB DDR3 memory On-board Storage Controllers –...
-
Page 18: Server Components
Figure 1-2 Overhead View of Server with the Top Cover Removed Hard Disk Drive (HDD) Bays and Front Panel The UV 20 server supports the 8 x 2.5”configuration of hard disk drives. Figure 1-3 shows the 8-bay configuration. -
Page 19: Control Panel
Control Panel Control Panel As shown in Figure 1-3, the control panel is in the top right portion of the front panel. Figure 1-4 shows the control buttons and LEDs on the control panel. Figure 1-4 Front Control Panel Table 1-2 identifies the components. -
Page 20: Back Panel
1: System Overview Back Panel Figure 1-5 shows the components on the back panel of the server. Figure 1-5 Back Panel 007-5900-001... -
Page 21: Table 1-3 Back Panel Components
Back Panel Table 1-3 identifies the components shown in Figure 1-5. Table 1-3 Back Panel Components Label Description Label Description USB ports I/O module ports/connectors (optional) USB ports Add-in adapter slots from riser card I/O module ports/connectors (optional) RMM4 NIC port (optional) Video connector Power supply module #2 NIC-1... -
Page 22: I/O Devices
1: System Overview I/O Devices The UV 20 server supports a variety of I/O devices such as hard drives, DVD drives, and SSDs. The connections for I/O devices are located on the front or back panel of the server, as shown in... -
Page 23: Hard Disk Drives
Hard disk drive bays USB ports USB ports Video port Hard Disk Drives The UV 20 server supports a maximum of 8 x 2.5” hard drives. For instructions on installing hard drives, “Installing Hot-Swap Hard Drives” on page Notes: •... -
Page 24: Solid-State Drives (Ssds)
1: System Overview Solid-State Drives (SSDs) The SSDs are mounted under a shelf behind the power supplies. The following items describe the UV 20 SSD support: • Up to two internal 2.5” SSDs are supported. • Two types of SSDs are supported: –... -
Page 25: System Safety
Basic electrical safety precautions should be followed to protect yourself from harm and the SGI UV 20 system from damage, as follows: • Be aware of the locations of the power on/off switch on the chassis as well as the room's emergency power-off switch, disconnection switch or electrical outlet. -
Page 26: Figure 2-1 Installing The Onboard Battery
2: System Safety • Serverboard Battery Caution: There is a danger of explosion if the onboard battery is installed upside down, which will reverse its polarites (see Figure 2-1). This battery must be replaced only with the same or an equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. -
Page 27: General Safety Precautions
Keep the area around the SGI UV 20 system clean and free of clutter. • The SGI UV 20 system might approach 75 lbs (38 kg) when fully loaded. When lifting the system, two people at either end should lift slowly with their feet spread out to distribute the weight. -
Page 28: Esd Precautions
2: System Safety ESD Precautions Caution: Electrostatic discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other. An electrical discharge is created to neutralize this difference, which can damage electronic com ponents and printed circuit boards. The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD: •... -
Page 29: System Operation And Monitoring
Chapter 3 System Operation and Monitoring Figure 3-1 shows the control panel at the top right of the front panel. There are several LEDs on the control panel as well as others on the hard drive carriers and power supplies. The LEDs keep you constantly informed of the overall status of the system as well as the activity and health of specific components. -
Page 30: Front Panel Controls And Leds
3: System Operation and Monitoring Front Panel Controls and LEDs The control panel contains control buttons and status LEDs. Figure 3-2 shows the components of a control panel. Figure 3-2 Control Panel Components Table 3-1 describes the control panel components and their functions. Table 3-1 Control Panel Components and Functions Label... - Page 31 Front Panel Controls and LEDs Table 3-1 Control Panel Components and Functions (continued) Label Button/LED Color Condition Function System ready/No alarm. Blink System ready, but degraded: – Redundancy lost such as the power supply or fan Green failure. – Non-critical temp/voltage threshold. –...
-
Page 32: Hard Disk Drive (Hdd) Leds
3: System Operation and Monitoring Notes: • Blink rate is ~1 Hz at 50% duty cycle. • It is also off when the system is powered off (S5) or in a sleep state (S1). • The power LED sleep indication is maintained on standby by the chipset. If the system is powered down without going through the BIOS, the LED state in effect at the time of power off is restored when the system is powered on until the BIOS clear it. -
Page 33: Table 3-2 Hdd Status Led Functions
Hard Disk Drive (HDD) LEDs Table 3-2 describes the functions of the Status LED. Table 3-2 HDD Status LED Functions LED Color Behavior Drive Status No access and no fault. Solid On Hard drive fault has occurred. Amber Blink – RAID rebuild in progress (1Hz). –... -
Page 34: Power Supply Led
3: System Operation and Monitoring Power Supply LED There is a single bi-color LED (green/amber) to indicate the power supply status. Table 3-4 describes the different states of the LED. Table 3-4 Power Supply LED States LED State Power Supply (PS) State No AC power to any PS. -
Page 35: Chassis Maintenance
Chapter 4 Chassis Maintenance For warranty and safety considerations, SGI designates the following chassis components as customer-replaceable units (CRUs): • Power supplies • Fans • Disk drives These components are all hot-swappable; that is, you can replace them without powering down the server. -
Page 36: Before You Start
4: Chassis Maintenance Before You Start Warning: Review the warnings and precautions listed in this manual before setting up or servicing this chassis. These include the items described in Chapter 2, “System Safety.” Tools and Supplies Needed • Phillips (cross head) screwdriver (#1 bit and #2 bit) •... -
Page 37: Removing And Installing The Front Fan Bezel
Removing and Installing the Front Fan Bezel Removing and Installing the Front Fan Bezel As shown in Figure 4-1, 7 of the 11 system fans are located at the front of the chassis and are covered by a bezel. Removing the Front Fan Bezel Follow these steps to remove the front fan bezel: Loosen the two screws on left and right ends. -
Page 38: Installing The Front Fan Bezel
4: Chassis Maintenance Installing the Front Fan Bezel Follow these steps to install the front fan bezel: Slide in the bezel. See A in Figure 4-2. 2. Secure the bezel to the chassis with the two screws on left and right ends. See B in Figure 4-2. -
Page 39: Removing The Rack Handles
Removing the Rack Handles Removing the Rack Handles To remove a rack handle, do the following: Remove the two screws holding the rack handle in place. Figure 4-3. 2. Remove the rack handle from the chassis. Figure 4-3. Figure 4-3 Removing a Rack Handle 007-5900-001... -
Page 40: Installing The Rack Handles
4: Chassis Maintenance Installing the Rack Handles To install a rack handle, do the following: Align the rack handle with the two holes on the side of the chassis. Figure 4-4. 2. Attach the rack handle to the chassis with two screws. Figure 4-4. -
Page 41: Removing The System Top Cover
Removing the System Top Cover Removing the System Top Cover The server system must be operated with the system cover in place to ensure proper cooling. You will need to remove the top cover to add or replace components inside of the server. Before removing the top cover, power down the server and unplug all peripheral devices and the power cable(s). -
Page 42: Figure 4-5 Removing The System Top Cover
4: Chassis Maintenance 5. Remove the screws. See A in Figure 4-5. 6. Depress the latches. See B in Figure 4-5. 7. Slide the cover back and lift upward. Figure 4-5 Removing the System Top Cover 007-5900-001... -
Page 43: Replacing The System Cover
Replacing the System Cover Replacing the System Cover To replace the system cover, use the following steps: Place the system cover onto the chassis and slide the cover forward to engage the recessed edge at the front of the cover. See A in Figure 4-6. -
Page 44: Replacing The Power Supply Modules
4: Chassis Maintenance Replacing the Power Supply Modules The system is equipped with two power supply modules for redundancy. They are hot-swappable. Note: A server configured with multiple GPGPU cards may not be configured with redundant power supplies. In this case, the power supplies are not hot-swappable. Removing the Power Supply Modules To remove the power supply modules, use the following steps: As shown in... -
Page 45: Installing The Power Supply Modules
Replacing the Power Supply Modules Installing the Power Supply Modules To install the power supply modules, use the following steps: Align and slide the module into the power supply cage as shown in Figure 4-8. 2. Push the module along the rail until the latch locks in position with a click. 3. -
Page 46: Installing Hot-Swap Hard Drives
4: Chassis Maintenance Installing Hot-Swap Hard Drives Caution: To maintain proper system cooling, use drive carriers with plastic drive blanks to populate drive days that would be otherwise empty. To install a HDD into the chassis, use the following steps. Remove the drive carrier by pressing the green latch to unlock it. -
Page 47: Figure 4-10 Removing Drive Blank
Installing Hot-Swap Hard Drives 3. Remove the four screws securing the plastic drive blank from the HDD carrier. See C in Figure 4-10. 4. Remove the plastic drive blank from the HDD carrier. See D in Figure 4-10. Figure 4-10 Removing Drive Blank 5. -
Page 48: Figure 4-12 Inserting Hdd Carrier Into Chassis
4: Chassis Maintenance 6. With the lever open, insert the hard disk drive assembly into the chassis and push in the lever to lock it into place. See F in Figure 4-12. Figure 4-12 Inserting HDD Carrier into Chassis 007-5900-001... -
Page 49: Replacing A Fan Module
Replacing a Fan Module Replacing a Fan Module As shown in Figure 4-13, seven of the system fans are located at the front of the chassis (front fans). The other four fans are in the middle of the chassis (middle fans). Figure 4-13 System Fans 007-5900-001... -
Page 50: Replacing A Front Fan
4: Chassis Maintenance Replacing a Front Fan To replace a front fan, do the following: Remove the front fan bezel. See section “Removing and Installing the Front Fan Bezel” on page 2. Pull the system fan straight out to remove it from the fan slot. Figure 4-14. -
Page 51: Replacing A Middle Fan
Replacing a Fan Module Replacing a Middle Fan To replace a middle fan, do the following: Remove the system cover. See section “Removing the System Top Cover” on page 2. Pull the system fan straight up to remove it from the fan slot. Figure 4-15. -
Page 52: Figure 4-16 Inserting A Middle Fan
4: Chassis Maintenance 3. Replace the system fan by guiding it into the slot and firmly pressing down to ensure that it is properly seated. Figure 4-16. Figure 4-16 Inserting a Middle Fan 007-5900-001... -
Page 53: Mounting The Chassis To A Rack
Mounting the Chassis to a Rack Mounting the Chassis to a Rack A slide rail kit is bundled with the server and is packed in the same shipping box with the chassis. Use the following steps to install the chassis in the rack. Remove the inner member from the slides as shown in Figure 4-17. -
Page 54: Figure 4-18 Attaching Slides To The Rack
4: Chassis Maintenance 2. Attach the slides to the rack as shown in Figure 4-18. Figure 4-18 Attaching Slides to the Rack 007-5900-001... -
Page 55: Figure 4-19 Installing The Inner Members To The Chassis
Mounting the Chassis to a Rack 3. Install the inner members to the chassis as shown in Figure 4-19. Figure 4-19 Installing the Inner Members to the Chassis 4. Install the chassis to the fixed slides as shown in Figure 4-20. -
Page 56: Removing The Chassis From A Rack
4: Chassis Maintenance Removing the Chassis from a Rack To remove the chassis from a rack, use the following steps: Extend the slides as shown in Figure 4-21. Figure 4-21 Extending Slides to Remove the Chassis 007-5900-001... -
Page 57: Figure 4-22 Removing The Inner Member From The Chassis
Removing the Chassis from a Rack 2. Remove the inner members from the chassis as shown in Figure 4-22. Figure 4-22 Removing the Inner Member from the Chassis 007-5900-001... -
Page 59: A Power And Environmental Specifications
Appendix A Power and Environmental Specifications This appendix describes the following: • “Power Rating” on page 45 • “Wattage Limitation of the PCI Loading” on page 46 • “Environmental Specifications” on page 46 Power Rating Table A-1 summarizes the power rating of the power supply. Table A-1 Power Rating of the Power Supply Total Available Power... -
Page 60: Wattage Limitation Of The Pci Loading
A: Power and Environmental Specifications Wattage Limitation of the PCI Loading Table A-2 summarizes the wattage limitation of the PCI loading. Table A-2 Wattage Limitation of the PCIe Loading Power Supply Configuration Maximum PCI Loading 90–140VAC 1600W (1+1) redundant, hot-swap capable 260W (AC low-line) 1600W (1+0 or 2+0) non-redundant... - Page 61 Environmental Specifications Table A-3 Environmental Specifications (continued) Attribute Limits +/-12 KV, except I/O port +/- 8 KV per test specification System cooling 1200 Watt Max – 4095 BTU/hour requirement in BTU/Hr 1600 Watt Max – 5459 BTU/hour 007-5900-001...
-
Page 63: B Regulatory Compliance Information
Appendix B Regulatory Compliance Information Table B-1summarizes the product regulatory compliance. Table B-1 Product Regulatory Compliance Compliance Information Category Electromagnetic FCC Class A, EN 55022 Class A, EN 61000-3-2/-3-3, CISPR 22 Class A Emissions Electromagnetic EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN Immunity 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11) Safety... -
Page 65: C Rail Kit Installation
Appendix C Rail Kit Installation If the chassis for your server does not have pre-installed rail slides, SGI provides a rail kit. Use the following steps to install the rail kit. Attach the slide rails to the racks as shown in Figure C-1. -
Page 66: Figure C-2 Extending Rail Slides
C: Rail Kit Installation 2. Fully extend the rail slides as shown in Figure C-2. Figure C-2 Extending Rail Slides 007-5900-001... -
Page 67: Figure C-3 Attaching Chassis To Rail Slides
3. Attach the chassis to the rail slides as shown in Figure C-3. Figure C-3 Attaching Chassis to Rail Slides 007-5900-001... -
Page 68: Figure C-4 Rail Slide Release Tab
C: Rail Kit Installation 4. Push the release tab and push the chassis into the rack as shown in Figure C-4. Figure C-4 Rail Slide Release Tab 007-5900-001... -
Page 69: Bmc Error Codes
Appendix D BMC Error Codes The BMC may generate beep codes upon detection of failure conditions. Beep codes are sounded each time the problem is discovered (for example, on each power-up attempt) but are not sounded continuously. Common supported codes are listed in Table D-1.
Need help?
Do you have a question about the UV 20 and is the answer not in the manual?
Questions and answers