This product is for professional use only! It is not for household use. The Atomic 3000 presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet radiation, and falls. Flashing light is also known to trigger epileptic seizures in persons who are photosensitive.
Page 5
15 minutes before handling. • Do not modify the fixture or install other than genuine Martin parts. • Do not operate the fixture if the ambient air temperature (Ta) exceeds 40° C (104° F).
90 to 260 volts. No adjustment is necessary. Note that the MAX-15 lamp does not operate below 125 volts. The current required by the Atomic 3000 varies according to lamp type, power mode, and usage. To avoid overload, allow one 16 or 20 amp branch circuit per fixture to operate the MAX-15 model at full power.
Page 7
Table 1: Cord cap wiring N S T A L L A T I O N The Atomic 3000 may be installed in any orientation. The mounting bracket provides five 12 mm holes for direct fastening or attachment of rigging clamps.
Page 8
3 Install a safety cable around the support and bracket. 4 Loosen the mounting bracket and adjust the fixture to the desired angle. 5 Connect and arrange the power and data cables. Preparation for use Atomic 3000 user manual...
A M P P O W E R S E T T I N G The Atomic 3000 provides high and low lamp power settings. The high power setting provides maximum flash intensity; the low power setting reduces output by approximately 50 percent and extends lamp life.
Page 10
Important: Use only replacement lamps from Martin! User only replacement lamps from Martin that have been prepared for use with an ionization wire. XOP lamps without an ionization wire will not work. A M P R E P L A C E M E N T End of life can be confirmed with the Flash LED on the rear panel.
For reliable data transmission use one input and one output! To connect the data link 1 Connect the DMX data input from the controller to the Atomic 3000’s 3-pin or 5-pin input (male) socket. 2 Connect up to 31 additional fixtures output-to-input.
Page 13
The address may be any channel from 1 to 511 and is set on the Address DIP switch. The Atomic 3000 uses 1, 3, or 4 channels depending on the control mode. For independent control, each fixture must be assigned its own address and non- overlapping control channels.
Page 15
L I N D E R E F F E C T The blinder effect, in which the light remains on for an extended period, is available in all DMX modes. In the 3- and 4-channel modes, the effect is achieved Atomic 3000 user manual Controller operation...
Page 16
To trigger single flashes, start with the intensity and flash rate at 0 and then set an intensity on channel 1. When the value of channel 1 changes, the light will flash once with the programmed intensity, duration, and effect. Controller operation Atomic 3000 user manual...
TAND ALONE OPERATION This section describes how to operate the Atomic 3000 in stand-alone mode without a DMX controller or Detonator remote control. T A N D A L O N E F L A S H R A T E To prog ram stand-alon e execution 1 Apply power to the fixture.
Page 18
Pin 10 OFF Switch open (off) Switch closed (on) Table 3: Remote stand-alone control Multiple fixtures can be controlled from the same switch if they are serially connected output-to-input. Do not terminate the link. Stand-alone operation Atomic 3000 user manual...
Pin 2 on the Mode DIP switch must be OFF. No other DIP switch setting is necessary. Connect the Atomic 3000 to the MC-1 as if it were a controller. See “Data connection” on page 12. Atomic 3000 user manual...
Page 20
A T A C O N N E C T I O N Important: Do not terminate the data link when using the Detonator! The Detonator connects to the Atomic 3000 with a 3-pin XLR data cable. Additional Atomic 3000s may be connected in series, output to input, for remote control of up to 20 fixtures.
Page 21
Single flashes can be achieved by pressing the Single Flash button with continuous flash stopped. The flash rate cycle can be restarted, for example to synchronize with a beat, by pressing the Single Flash button while continuous flash is running. Atomic 3000 user manual Remote controls...
U S E R E P L A C E M E N T The Atomic 3000 uses a 20 amp time-delay fuse for protection against current overload. If the power diode does not light when power is applied, the fuse may be spent.
PROTOCOLS D M X C H A N N E L M O D E Channel Value Percent Function 0 - 5 0 - 1 Blackout 6 - 249 2 - 98 Flash rate, slow to fast 250 - 255 98 - 100 Continuous “Blinder”...