NTRODUCTION Thank you for selecting the Martin FiberSource QFX 150. This fiber optic lighting fixture uses a long-life 150 watt discharge lamp and provides 4 colors plus white, full-range dimming, and a variable-speed twinkle effect. It operates with DMX-512 controllers, in stand-alone mode, and in master/slave configuration.
Page 5
• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents. • Allow the fixture to cool before handling. • Do not modify the fixture or install other than genuine Martin parts. • Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
The FiberSource QFX 150 is designed for use with the Osram HQI-R 150 lamp. Do not install any other type of lamp. Warning! Disconnect the fixture from power and allow it to cool before opening. Important! Turn the lamp so that the arc is horizontal.
POWER The FiberSource QFX 150 has 10 switch-selectable power supply settings. Always use the setting that is closest to the local AC supply. Warning! For protection from electric shock, the fixture must be grounded (earthed). The power supply shall have overload and ground- fault protection.
Page 8
To inst all the main f use Fuses are provided for 100 - 130 V and 200 - 250 V operation. Use only the fuse specified for the operating voltage. 1 Locate the bag containing the fuse for your AC voltage. Insert the fuse in the fuse holder.
NSTALLATION The FiberSource QFX 150 can be fastened directly through the 4 rubber washers in the mounting flanges, or hung with 2 rigging clamps (not included) fastened through the 13 mm holes. I N S T A L L A T I O N R E Q U I R E M E N T S For optimum performance and ease of service, install the fixture such that •...
Page 10
4 If clamping, bolt the clamps securely to the flanges with grade 8.8 (minimum) M12 bolts and lock nuts, or as recommended by the clamp manufacturer, through the 13 mm holes. Install a safety cable that can hold at least 10 times the weight of the fixture through one of the small holes and around the truss or pipe.
IBER OPTIC CABLE The FiberSource male adaptor for 50 - 300 strand cables, P/N 91611016 (not included), is tapered to fit fiber optic cables 8.3 - 19.3 mm (5/16 - 3/4 in.) in diameter. With cables over 8.3 mm in diameter, the adaptor must be shortened for proper fit and maximum light output.
RS-485 applications. Your Martin dealer can supply high quality cable in various lengths. The FiberSource QFX 150’s data sockets are wired pin 1 to ground, pin 2 to signal - (cold), and pin 3 to signal + (hot). This is the standard pin assignment for DMX devices.
Page 13
A control address must be set using the DIP-switch on the rear panel. The control address, also known as the start channel, is the first channel used to receive instructions from the controller. The FiberSource QFX 150 uses 5 DMX channels. Each fixture must be assigned its own address and non-overlapping control channels for individual control.
Page 14
D I P - S W I T C H A D D R E S S T A B L E Find the address in the table below. Read the settings for pins 1 - 5 to the left and read the settings for pins 6 - 9 above the address.
Page 15
C O N T R O L L A B L E E F F E C T S L A M P P O W E R A N D R E S E T The lamp on command is on channel 1, the address channel. When set up for controller operation, the lamp remains off until a lamp-on command is sent.
ALONE OPERATION C O N T R O L O P T I O N S The FiberSource QFX 150 can be operated without a controller in stand-alone mode. This mode provides various combinations of color and twinkle effect that are selected using DIP-switch pins 1 - 7.
Page 17
Important! DIP-switch pin 10 must be ON for stand-alone operation. 0 = OFF 1 = ON Effect Setting no twinkle slow twinkle medium twinkle fast twinkle snap color change slow color change medium color change fast color change white color 1 color 1 - 2 color 1 - 4 color 1 - 6...
ASTER SLAVE OPERATION Several FiberSource QFX 150s may be connected together for synchronous operation without a controller. They are connected together and one, the master, is set up in stand-alone mode and sends control instructions to the others. Up to 32 fixtures can be can be connected and operated this way.
ASIC SERVICE The FiberSource QFX 150 requires simple routine maintenance. The maintenance schedule depends heavily on the operating environment; please consult a Martin service technician for recommendations. Any service procedure not described here should be referred to a qualified technician.
Page 20
the cable socket. Center the section and then support the wheel with a finger from the front as you press the 2 screw heads through the wheel. 5 Replace the lamp access cover before applying power. To clean opti cal component s Use care when cleaning optical components.
Page 21
To replace t he secondary fuse 1 Disconnect the fixture from power. 2 Remove one screw by the DIP-switch and one screw by the data IN socket. 3 Pull the circuit board assembly out until you can access the fuse, which is located behind the data IN socket.
One of the fixtures is regained: unplug both cables transmitting as a master or is from fixture and connect them defective. directly together. Contact Martin technician for service. An effect requires mechanical Contact Martin technician for Fixture fails to reset correctly. adjustment. service.