Settings; Ethernet; E-Mail Address - Mitsubishi Electric DX-TL2500E Installation And Operation Manual

1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } <COMMUNICATION PORT
SETTINGS> } Select "MODE" in the <RS-232C> screen.
Display the desired setting and confirm.
2. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.

• SETTINGS

RS-232C settings can be made when setting "MODE"
above to "REMOTE A", "REMOTE B" or "REMOTE C".
Perform settings so that the settings are the same
with the connecting PC.
Setting of "TRANSMISSION MODE" ( default : "9600" )
"1200", "2400", "4800", "9600", "19200"
Setting of "DATA BIT LENGTH" ( default : "8BIT" )
"8BIT", "7BIT"
Setting of "PARITY BIT" ( default : "NONE" )
"NONE", "ODD", "EVEN"
Setting of "STOP BIT LENGTH" ( default : "1BIT" )
"1BIT", "2BIT"
Setting of "DELIMITER" ( default : "CR" )
"CR", "CR•LF"
1. Set "MODE" in the <RS-232C> screen to "REMOTE A",
"REMOTE B" or "REMOTE C".
2. Select "SETTINGS" and turn the SHUTTLE ring clockwise.
• The <RS-232C SETTINGS> screen appears.
<RS-232C SETTINGS>
>>TRANSMISSION MODE
DATA BIT LENGTH
PARITY BIT
STOP BIT LENGTH
DELIMITER
3. Select the setting to change and turn the SHUTTLE ring
clockwise.
• The background of the setting turns red and flashes.
4. Display the desired sub item and turn the SHUTTLE ring
clockwise.
• The setting is confirmed and flashing stops.
5. To make additional changes, repeat steps 3 and 4.
6. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.

ETHERNET

The IP address used to specify the connected recorder, sub
net mask setting, and MAC address can be referred to here.
Do not assign "000.000.000.000" IP address. And do
not assign it as the broadcast address. If this address were
to be assigned, we could not guarantee communications or
any other functions of the recorder unit.
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select "ETHERNET" in the
<COMMUNICATION PORT SETTINGS> screen and turn the
SHUTTLE ring clockwise.
• The <ETHERNET> screen appears.
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
2. Select the setting you wish to alter by turning the JOG dial
and then turn the SHUTTLE ring clockwise.
• The leftmost number of the setting will reverse in color.
3. Turn the JOG dial to reverse display the number you wish
to alter and turn the SHUTTLE ring clockwise.
• The background of the selected number turns red and flashes.
4. Turn the JOG dial to display the desired number and turn
the SHUTTLE ring clockwise.
• The setting is confirmed and flashing stops.
5. Repeat steps 2 and 4 to change the other numbers.
The setting can not be changed during the record.
Stop the record to change the setting.
When change the setting the power turns off auto-
matically, then the unit will boot up.
Press the SET UP button to return to the normal
screen without changing the setting.
When any setting of "IP ADDRESS", "SUB NET
MASK", "GATEWAY" is changed turn the SHUTTLE
ring counterclockwise during the cursor is on the left of
9600 the setting on the screen.
8BIT
NONE

• E-MAIL ADDRESS

1BIT
CR The contents of the setting of "SMTP SERVER", "RE-
CORDER ID" and "USER ADDRESS" can be referred
to here.
The specific software is required to input "SMTP
SERVER", "RECORDER ID" and "USER ADDRESS".
Please refer to the instruction manual of the software.
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } <COMMUNICATION PORT SETTING>
} select "E-MAIL ADDRESS" in the <ETHERNET> screen.
• The <E-MAIL ADDRESS> screen appears.
"E-MAIL ADDRESS" is displayed only for 20 char-
acters from the beginning.
<ETHERNET>
>>IP ADDRESS 192.168.000.100
SUB NET MASK 255.255.255.000
GATEWAY 000.000.000.000
E-MAIL ADDRESS
SERVICE PORT SETTING
ALARM NOTIFICATION SETTING
<MAC ADDRESS>
08-00-70-2E-3F-FF
PLEASE PRESS SET UP BUTTON
TO APPLY NEW SETTING
<E-MAIL ADDRESS>
SMTP SERVER
RECORDER ID
USER ADDRESS
1
2
3
4
5
55