Warnings And Call Out Output; Warnings And Their Appropriate Countermeasures - Mitsubishi Electric DX-TL2500E Installation And Operation Manual

Warnings and CALL OUT output

Warnings and their appropriate countermeasures

#1 Options in the CALL OUT options column:
• Selectable : CALL OUT output can be selected/de-selected on the menu.
• Fixed : a CALL OUT signal is emitted without prior selection of this function using the menu.
• None : no CALL OUT signal is emitted, but a warning indicator will appear on screen.
CALL OUT signal output can be stopped by pressing the WARNING RESET button.
Warning Display
REC/FULL
REC/SUB FULL
REC/LPA FULL
COPY/FULL
REST/FULL
ARCHIVE/FULL
REC/REM
ARCHIVE/REM
COPY/SIZE/
DATA ERROR
REST/SIZE/
DATA ERROR
ARCHIVE/SIZE/
DATA ERROR
COPY/
MEDIA ERROR
REST/
MEDIA ERROR
ARCHIVE/
MEDIA ERROR
COPY/NO MEDIA
REST/NO MEDIA
ARCHIVE/
NO MEDIA
NO SIGNAL
(The warning will
indicate the number
of the non-functioning
camera. )
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
92
Status
• MAIN HDD recordable • When the warning is
cancelled, the unit will start
capacity is full.
over-writing the oldest data
• SUB HDD recordable
remaining in the hard disk
capacity is full.
drive.
• LPA HDD recordable
• Copy data as necessary.
capacity is full.
• Replace with new media.
• Media recordable
capacity is full. • Replace media if necess
-ary.
• Copy data as necessary.
• The remaining HDD capa
-city has reached the value
set in HDD REMAIN.
• The data that is being • Set the copy/restore
range again.
copied/restored exceeds
• Replace with new media.
the capacity of the recor
-ding device, or there is
no original data.
• Check media in recording
• Error has occurred in the
media as recording device. device. (Insert the media
if there is none.)
• Check whether it is write-
protect by media. It will
cancel, if protected.
• After peripheral recording
device and the unit power off
a power supply, reboot in
order of peripheral recording
device and the unit.
• After peripheral recording
device and the unit power
off a power supply, please
perform the check of a
SCSI cable and termination.
• Insert the media.
• No inserted media.
• Check whether the unit
• Video signal was lost for
and camera are properly
more than 5 seconds
connected, and that electri
during recording.
-city is on.
• Check whether the visual
signal is being properly
outputted.
• Check to see if there is a
camera set for operation
with no video signal input.
Canceling
Countermeasure
the warning
Press the
WARNING
RESET button.
Press the
WARNING
RESET button.
Press the
WARNING
RESET button.
Press the
WARNING
RESET button.
Press the
WARNING
RESET button.
Press the
WARNING
RESET button.
Stop recording.
Output video
signals.
Press the
WARNING
RESET button.
CALL OUT
Code page
output
#1
WNG1100 Selectable 49
WNG1101
-
WNG1102
-
WNG3100 None
12
WNG4100
Selectable
WNG7100
WNG1200 Selectable 53
(MAIN)
WNG1201
(SUB)
WNG1202
(LPA)
WNG7200
WNG3701 None 12, 16
WNG4701 76,77
WNG7701
None
WNG3702 12, 16
WNG4702 76,77
WNG7702
-
-
16
None
WNG3703 12, 16
WNG4703
WNG7703
WNG54 #3 Fixed 15
37
23, 24
43-45