Remain Hdd; Call Out Settings; Hdd Main Remain/Hdd Sub Remain/Hdd Lpa Remain/Archive Remain - Mitsubishi Electric DX-TL2500E Installation And Operation Manual

Setting ( default : "OFF" )
"REMAIN", "WARNING", "ALARM", "OFF"
SETTING
BUZZER
When reaching the remaining
capacity set in "REMAIN HDD"
When a failure occurs and
a warning is displayed
When an alarm recording or
emergency recording is started
1. Press the SET UP button } <SETTINGS> } <INITIAL SET UP/
INFORMATION> } Select "BUZZER" in the <REAR TERMINAL
SETTINGS> screen. Display the desired setting and confirm.
2. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.

REMAIN HDD

A warning indicating that the either remaining capacity
of HDD or archive device has become low during re-
cording is outputted. The device can be selected and
the remaining capacity can be set here.
<REAR TERMINAL SETTINGS>
MODE OUT 1
MODE OUT 2
MODE OUT 3
MODE OUT 4
MODE OUT 5
KEY SOUND
BUZZER
>>REMAIN HDD

CALL OUT SETTINGS

EMERGENCY REC DURATION
A warning is outputted using the following methods
when the remaining capacity becomes low during re-
cording.
• The HDD usage display flashes when "3" is set to
"DISPLAY MODE" in the <TIME DATE/DISPLAY SET-
TINGS> screen.
• A buzzer will sound when "REMAIN" is set to "BUZZER"
in the <REAR TERMINAL SETTINGS> screen.
Setting of DEVICE ( default : "MAIN" )
"MAIN" : Displays a warning of low MAIN HDD capacity.
"SUB" : Displays a warning of low SUB HDD capacity.
"LPA" : Displays a warning of low LPA HDD capacity.
"ARCHIVE" : Displays a warning of low archive device
capacity.
"OFF" : Does not display warning of low capacity.
"SUB" is appeared when "PARTITION" ("LONG
PRE-ALARM") is selected on "HDD SETTING" of the
<INITIALIZATION> screen.
"LPA" is appeared when "LONG PRE-ALARM" is
selected on "HDD SETTING" of the <INITIALIZATION>
screen after installing EXTRA HDD to "INTERNAL HDD
A".
Setting of "REMAIN HDD" ( default : "10%" )
"2%", "4%", "6%", "8%", "10%", "15%","20%", "30%",
"40%", "50%"
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
REMAIN WARNING ALARM OFF
ON OFF OFF OFF
OFF ON OFF OFF
OFF OFF ON OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
MAIN-10%
10M
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } "Select "REMAIN HDD" in the <REAR
TERMINAL SETTINGS> screen and turn the SHUTTLE ring
clockwise twice.
• The setting display reverses in color when the SHUTTLE
ring is turned the first time. When the ring is turned for the
second time, the background turns red and flashes.
2. Turn the JOG dial to display the desired device and turn the
SHUTTLE ring clockwise.
• The setting is confirmed and flashing stops.
3. Turn the JOG dial clockwise to move the reversed display to
the REMAIN HDD value and turn the SHUTTLE ring clockwise.
• The background of the REMAIN HDD value turns red and flashes.
4. Turn the JOG dial to display the desired capacity and turn
the SHUTTLE ring clockwise.
• The setting is confirmed and flashing stops.
5. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.
CALL OUT SETTINGS
The CALL OUT setting is a setting to notify to the outside
warning signals outputted by this device by outputting the
signals from the CALL OUT terminal on the rear.
CALL OUT SETTINGS use photo-coupler output
to decrease the amount of malfunctions due to wiring.
See page 15 "CALL OUT Output terminal" for apt
connection procedures.
• HDD MAIN REMAIN/HDD SUB REMAIN/HDD LPA
REMAIN/ARCHIVE REMAIN
When the remaining memory in the HDD or ARCHIVE
device reaches the set value, the unit outputs a signal
from the CALL OUT terminal, and the "REC/REM" or
"ARCHIVE/REM" warning displayed on the screen.
<CALL OUT SETTINGS>
>>HDD MAIN REMAIN
HDD MAIN FULL
HDD SUB REMAIN
HDD SUB FULL
HDD LPA REMAIN
HDD LPA FULL
ARCHIVE REMAIN
ARCHIVE FULL
"HDD SUB REMAIN" is appeared when "PARTI-
TION" ("LONG PRE-ALARM") is selected on "HDD
SETTING" of the <INITIALIZATION> screen.
"HDD LPA REMAIN" is appeared when "LONG
PRE-ALARM" is selected on "HDD SETTING" of the
<INITIALIZATION> screen after installing EXTRA HDD
to "INTERNAL HDD A".
"ARCHIVE REMAIN" is appeared when "ARCHIVE•
COPY" is selected on "ID4•ID5" of the <INITIALIZA-
TION> screen.
Setting ( default : "OFF" )
"2%", "4%", "6%", "8%", "10%", "15%", "20%", "30%",
"40%", "50%", "OFF"
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
53