Rear Terminal Settings; Mode Out 1 ~ Mode Out 5; Key Sound; Buzzer - Mitsubishi Electric DX-TL2500E Installation And Operation Manual

<INITIAL SET UP/INFORMATION> (continued)
• Audio recording cannot be performed when "PPS" of
"RECORD SETTING" are all set to smaller than
"0.333P" when setting normal recording. In this case,
( X ) appears to the right of recordable time display.
• When the camera selection during alarm recording is
as follows :
"ALARM CH" : "A-PPS" of all cameras set for alarm
recording are set to smaller than "0.333P".
"ALARM PLUS", "ALARM25" : "PPS" and "A-PPS" of
all cameras set for normal recording and alarm record-
ing are set to smaller than "0.333P".

REAR TERMINAL SETTINGS

MODE OUT 1 ~ MODE OUT 5

The unit status can be outputted from the MODE OUT termi-
nals on the rear. There are 5 MODE OUT terminals and each
terminal can be set to generate a certain type of output.
<REAR TERMINAL SETTINGS>
>>MODE OUT 1
MODE OUT 2
MODE OUT 3
MODE OUT 4
MODE OUT 5

KEY SOUND

BUZZER

REMAIN HDD
CALL OUT SETTINGS
EMERGENCY REC DURATION
Setting ( default : "OFF" )
"REC" : Outputs signals during recording.
"PLAY" : Outputs signals during playback.
"REMAIN" : Outputs signals when the remaining HDD
device or archive device space reaches the value speci-
fied in "REMAIN HDD".
"POWER" : Outputs signals when the power of the unit
turns on.
"MOTION1" ~ "MOTION5" : Outputs the camera num-
bers detected during motion detection recording using
binary notation (MODE OUT 1 ~ MODE OUT 5 are
linked). Furthermore, motion detection inputted the last
is maintained for 2 seconds.
Relation between a camera number and a MODE OUT output
MODE OUT terminals
1 2 3
O X X
1
X O X
2
3 O O X
X X O
4
5 O X O
6 X O O
O O O
7
8 X X X
9
O X X
10 X O X
11 O O X
12 X X O
O X O
13
14 X O O
15 O O O
16 X X X
"ALARM" : Outputs signals during alarm recording.
"OFF" : No signal is outputted.
Capacity warning from MODE OUT is only outputted
during recording.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
52
OFF
OFF
OFF
OFF
OFF
ON
OFF
MAIN-10%
10M
4 5
X X
O : Signal is outputted.
X X
X : No signal is outputted.
X X
X X
X X
X X
X X
O X
O X
O X
O X
O X
O X
O X
O X
X O
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select "REAR TERMINAL
SETTINGS" screen.
2. From the 5 MODE OUT terminals, display the desired setting
for the terminal (MODE OUT 1 ~ MODE OUT 5) to output
signals and then confirm.
3. To set other terminals, repeat step 2.
4. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.
KEY SOUND
It is possible for the unit to make button sounds when
using the operation buttons on the front of the unit or
when operating the JOG dial or SHUTTLE ring.
<REAR TERMINAL SETTINGS>
MODE OUT 1
MODE OUT 2
MODE OUT 3
MODE OUT 4
MODE OUT 5
>>KEY SOUND
BUZZER
REMAIN HDD
CALL OUT SETTINGS
EMERGENCY REC DURATION
1. Press the SET UP button } <SETTINGS> } <INITIAL SET UP/
INFORMATION> } Select "KEY SOUND" in the <REAR TERMINAL
SETTINGS> screen. Display the desired setting and confirm.
2. Turn the SHUTTLE ring counterclockwise or press the SET
UP button.
BUZZER
It is possible for a buzzer to sound when the remaining
HDD device or archive device space reaches the value
set in "REMAIN HDD" of the <REAR TERMINAL SET-
TINGS> screen. Other than the above, it is possible to
set the buzzer to sound when starting alarm recording
or emergency recording, or when a warning is displayed.
<REAR TERMINAL SETTINGS>
MODE OUT 1
MODE OUT 2
MODE OUT 3
MODE OUT 4
MODE OUT 5
KEY SOUND
>>BUZZER
REMAIN HDD
CALL OUT SETTINGS
EMERGENCY REC DURATION
To sound a buzzer only when reaching a specified value :
1) Select "REMAIN" for "BUZZER" in the <REAR TER-
MINAL SETTINGS> screen.
2) Set the remaining capacity in "REMAIN HDD" of the
<REAR TERMINAL SETTINGS> screen.
To sound a buzzer when reaching the set remaining ca-
pacity or when a warning is displayed :
1) Select "WARNING" for "BUZZER" in the <REAR TER-
MINAL SETTINGS> screen.
2) Set the remaining HDD capacity (HDD MAIN RE-
MAIN/HDD SUB REMAIN/HDD LPA REMAIN/ARCHIVE
REMAIN) in "CALL OUT SETTINGS" of the <REAR
TERMINAL SETTINGS> screen.
OFF
OFF
OFF
OFF
OFF
ON
OFF
MAIN-10%
10M
OFF
OFF
OFF
OFF
OFF
ON
OFF
MAIN-10%
10M