All/Perimeter System Arming - Security Command Executive XR200 User Manual

Executive series
Hide thumbs Also See for Executive XR200:
Table of Contents

Advertisement

All/Perimeter System Arming

Area Assignment: Your security system is divided into two separate
areas. Motion detectors, inside doors, and other interior protection
devices are assigned to the Interior area while windows and exterior
doors are assigned to the Perimeter area.
Perimeter or All: When you go to arm an All/Perimeter system, the
Security Command keypad displays PERIM ALL. If you select
ALL, you're arming both the Perimeter and the Interior areas of the
system. You'll want to arm both of these areas when leaving the
premises with nobody left inside. Selecting PERIM arms only the
perimeter of the system. Perimeter arming is for when you're staying
inside but want the comfort of knowing the exterior doors and
windows are armed. Perimeter arming allows you to move freely
about inside without setting off any interior alarms.
Instant: During the exit delay time, you can cancel the exit and entry
delays and cause all zones to be instant zones. Just press the far
right SELECT key under INSTNT while the exit delay is displayed.
This immediately arms the exit zones. However, no entry delay is
provided and an alarm will occur should an entry door be opened.
Arming an All/Perimeter System
1. Press the COMMAND key until PERIM
2. Select ALL to arm both the perimeter and interior areas. Press
PERIM to arm the perimeter area only.
3. Enter your user code if required.
All/Perimeter System Arming
Area Assignment: Your security system is divided into two separate
areas. Motion detectors, inside doors, and other interior protection
devices are assigned to the Interior area while windows and exterior
doors are assigned to the Perimeter area.
Perimeter or All: When you go to arm an All/Perimeter system, the
Security Command keypad displays PERIM ALL. If you select
ALL, you're arming both the Perimeter and the Interior areas of the
system. You'll want to arm both of these areas when leaving the
premises with nobody left inside. Selecting PERIM arms only the
perimeter of the system. Perimeter arming is for when you're staying
inside but want the comfort of knowing the exterior doors and
windows are armed. Perimeter arming allows you to move freely
about inside without setting off any interior alarms.
Instant: During the exit delay time, you can cancel the exit and entry
delays and cause all zones to be instant zones. Just press the far
right select key under INSTNT while the exit delay is displayed. This
immediately arms the exit zones. However, no entry delay is
provided and an alarm will occur should an entry door be opened.
Arming an All/Perimeter System
1. Press the COMMAND key until PERIM
2. Select ALL to arm both the perimeter and interior areas. Press
PERIM to arm the perimeter area only.
3. Enter your user code if required.
4. The system displays any Bypassed zones or bad 24 hour or
5. At this point you can force arm or bypass any bad zones. A
6. The keypad displays PERIMETER ON if only the perimeter is
7. The keypad next displays EXIT: ## INSTNT and begins to
8. You can select INSTNT while EXIT: ## INSTNT is displayed to
ALL is displayed.
9. When the system is fully armed, the keypad displays
4. The system displays any Bypassed zones or bad 24 hour or
5. At this point you can force arm or bypass any bad zones. A
6. The keypad displays PERIMETER ON if only the perimeter is
7. The keypad next displays EXIT: ## INSTNT and begins to
8. You can select INSTNT while EXIT: ## INSTNT is displayed to
ALL is displayed.
9. When the system is fully armed, the keypad displays
Priority zones. A bad Priority zone cannot be armed.
zone that is force armed will be restored into the system if it later
returns to normal. A zone that is bypassed will remain bypassed
until the system is disarmed. See steps 5a through 5d.
5a. If a problem exists on a zone, the zone name and problem
is shown followed by OKAY BYPASS STOP.
5b. Select OKAY to force arm the zone(s) before arming.
5c. Select BYPASS to bypass the zone(s) before arming.
5d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
being armed and ALL SYSTEM ON if both the perimeter and
interior are being armed.
count down the number of seconds remaining for you to exit.
When the delay expires, the exit zones are armed.
immediately arm all exit zones and make them instant. The
keypad displays INSTANT.
PERIMETER ON for perimeter arming and ALL SYSTEM ON
for perimeter and interior arming.
Priority zones. A bad Priority zone cannot be armed.
zone that is force armed will be restored into the system if it later
returns to normal. A zone that is bypassed will remain bypassed
until the system is disarmed. See steps 5a through 5d.
5a. If a problem exists on a zone, the zone name and problem
is shown followed by OKAY BYPASS STOP.
5b. Select OKAY to force arm the zone(s) before arming.
5c. Select BYPASS to bypass the zone(s) before arming.
5d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
being armed and ALL SYSTEM ON if both the perimeter and
interior are being armed.
count down the number of seconds remaining for you to exit.
When the delay expires, the exit zones are armed.
immediately arm all exit zones and make them instant. The
keypad displays INSTANT.
PERIMETER ON for perimeter arming and ALL SYSTEM ON
for perimeter and interior arming.
Arming and Disarming
9
Arming and Disarming
9

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Executive XR200 and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents