Output Function Programming: Program Addresses (2772-2843) - Bosch DS7400Xi Reference Manual

10.37 Output Function Programming: Program Addresses (2772-2843)

Output programming allows you to have the Outputs follow status events by partition or system-wide, or follow zone outputs in an Input/
Output Cross Matrix. See the Programming Addresses Worksheet (P/N: 43850) for a description of each address. See Glossary
(section 6.4) for further details.
Latch ON after Zone Alarm
ON during Entry Pre-Alert
ON when system is armed
Zone alarm
Zone Alarm delayed by 20 sec.
Keypad Sounder output
Access output (10 sec. pulse)
Keyfob output
Panic/Duress output**
Follow System Status Event
Follow a single zone
Follow two zones-When EITHER zone changes state
Follow two zones-When BOTH zones change state
Data Digit
1 2
*2
Select Option
AC Power Failure
Low Battery
Communication Failure
System Fault**
Keypad Supervision Fault
Multiplex Bus Fault
*0 - *2 are Hex values. They will display as A - C at the keypads.
**System Faults include:
• RAM fault
• ROM fault
• Bell/Line Monitor fault (DS7420i)
• Line 1 fault
• Line 2 fault
• Bell fault
• Aux. Power fault
• Octal Relay fault
• Serial Module fault (DS7412)
Output Program
Function
Address
Number
1 2772
2 2775
3 2778
4 2781
5 2784
6 2787
7 2790
8 2793
9 2796
10 2799
11 2802
12 2805
13 2808
14
2811
15
2814
16 2817
17 2820
18
2823
19 2826
20
2829
21
2832
22
2835
23 2838
24 2841
Page 66 P/N: F01U035325-01
Select Option DD
*0
*1
*2
*3
*4
*5
*0-*5 are Hex values. They will
display as A-F at the keypads.
DD DD
Select Option
1 7 Radio Receiver Fault
2 8 Aux Power Fault
3 9 Fire Trouble
4 *0 Supervisory
5 *1 Zone Trouble
6 *2 Duress PIN
• Serial Transmit fault
• Serial Receive fault
• Aux. Relay fault
• DS7416i Communications fault
• RF Receiver Tamper
• RF Receiver Jammed
• RF Receiver Trouble
• Printer Off-line
Program
Program
Address Address
2773 2774
2776 2777
2779 2780
2782 2783
2785 2876
2788 2789
2791 2792
2794 2795
2797 2798
Activate:
2800 2801
2803 2804
Disabled
2806 2807
2809 2810
When zone is shorted
2812
2813
2815
2816
When Zone is opened
2818
2819
2821
2822
When panel is Armed
2824 2825
2827
2828
When panel is not Armed
2830 2831
2833
2834
Latch when activated**
2836 2837
2839
2840
** = This is only for DS7465 Outputs. DS7488 Outputs will not latch when this is selected.
2842
2843
Copyright © 2007 Bosch Security Systems, Inc.
Data Digit 1 Options 1-9 and *1 are used to program an Output
Function to follow status events for individual partitions.
0 Data Digit 1 Option *0 is used to program an Output
Function to follow the Wireless Keyfob Output Buttons.
1
Data Digit 1 Option *2 is used to program an Output
3 Function to follow status events system-wide.
Data Digit 1 Options *3-*5 are used to program an Output
6
Function to follow a zone or two zones in an Input/Output
7
Cross Matrix.
8
Data Digit
Program
9
1
Address
1
Option RF3334
Disabled
Moment
Option
Toggle Option
Moment
Toggle
Data Digit
1 2
3
Data Digit
Follows 0
Disabled
Armed Full
Armed Partial
Armed Any
0 1
Program
Address
2
1
DD
Follows
0
Disabled
1
Key
2
Key
Burglar Alarm
3
Fire Alarm
4
Program Program
Address Address
1 2
Data Digit Data Digit Data Digit
1 1 2 2 1
Enter the
Zone Number
of First Zone
to Follow
(see Zone
HEX Values
chart)
1 2 3
Enter Data Digit as a:
2 3 4 5 6 7 8
DS7400Xi (4+) Reference Guide
Data Digit
1 2
Data Digit
0 1 2 3
Program
Address
3
Data Digit
2 1 2
Enter the
Zone Number
of Second
Zone to
Follow
(see Zone
HEX Values
chart)
Not Required
if following a
single zone
9 *0 *1 *2