Setting The Remote Control To Operate Your Tv; Television Operation; Operating Other Panasonic Dvd Equipment With The Remote Control - Panasonic DMR-E20 Operating Instructions Manual

TV
VOL
2
TV/AV
OPEN/CLOSE
PROG / CHECK ENTER RETURN
TOP WINDOW STATUS
FRAME
TV ASPECT TV/TEXT
SKIP SLOW/SEARCH
STOP PAUSE PLAY
1 2 3
4 5 6
7 8 9
SV/V+
0 /
REC REC MODE
CANCEL
MANUAL INPUT
TIME SLIP
SKIP SELECT
DIRECT
LAST
TV REC
AV LINK AUDIO
MARKER
TIMER
DVD TV
SETUP
REC
Á
TV
VOL
TV/AV
OPEN/CLOSE
PROG / CHECK ENTER RETURN
TOP WINDOW STATUS
FRAME
TV ASPECT TV/TEXT
SKIP SLOW/SEARCH
STOP PAUSE PLAY
1 2 3
4 5 6
7 8 9
SV/V+
0 /
REC REC MODE CANCEL
MANUAL INPUT
TIME SLIP
SKIP SELECT
DIRECT
LAST
TV REC
AV LINK AUDIO
MARKER
TIMER
DVD TV
SETUP
REC
Á

Setting the remote control to operate your TV

Television operation

You can control televisions by changing the remote control code.
Preparation
≥Turn on the television.
≥Switch [DVD, TV] to "TV".
1
Refer to the chart below for the code for your television.
Press and hold [TV, Í] and enter the two-digit code with the numeric
2
buttons.
≥For example: 01, press [0] )[1].
≥After entering the code, test the remote control by turning on the television and changing
channels.
Note
≥If there is more than one code, repeat the procedure until you find the code that allows correct
operation.
≥Repeat this procedure after you change the batteries.
≥If your television brand is not listed or if the code listed for your television does not allow control
of your television, this remote is not compatible with your television.
List of TVs Compatible with the unit's Remote Control
Brand: Code
Panasonic 01, 02, 03, 04
AIWA 35
AKAI 27, 30
BLAUPUNKT 09
BRANDT 10, 15
BUSH 05, 06
CURTIS 31
DESMET 05, 31, 33
DUAL 05, 06
ELEMIS 31
FERGUSON 10
GOLDSTAR/LG 31
GOODMANS 05, 06, 31
GRUNDIG 09
HITACHI 22, 23, 31, 40, 41, 42
INNO HIT 34
IRRADIO
30
ITT 25
JVC 17, 39
LOEWE 07
METZ 28, 31
MITSUBISHI 06, 19, 20
MIVAR 24
NEC 36
Operation: Button
[TV, Í]
On and off:
Video input mode: [TV, TV/AV]
[TV, W, X]
Channels:
[TV, VOL, i, j]
Volume:
Operation
These operating instructions describe operations mainly using the remote control. If the name of
the button is the same, the operation described can also be performed with the main unit.
The displays shown in these instructions are examples only. Actual displays depends on the disc
being played.
Operating other Panasonic DVD equipment with the remote
control
By changing the remote control code, you can operate other DVD recorders and players
manufactured by Panasonic.
Most of the DVD recorders and players manufactured by Panasonic use the same system for
their remote controls, so if you operate them in the same place, the controls can be confused by
the different pieces of equipment. Use the following procedure to change the remote control code
to solve this problem.
≥Use "1", the factory set code, under normal circumstances.
Preparation
Switch [DVD, TV] to "DVD".
Press [Í] and the numeric buttons corresponding to the code you want to set,
[1], [2], or [3], at the same time.
Note
≥Be sure to set the same remote control code on the main unit as you did for
the remote control itself (page 80, Setting s — Remote).
≥The display on the right appears on the unit's display if its code and the
remote control's code are different. Change the remote control's code to suit
the unit.
≥The display disappears after about 5 seconds.
10
Brand: Code
NOKIA 25, 26, 27
NORDMENDE 10
ORION 37
PHILIPS 05, 06
PHONOLA 31, 33
PIONEER 38
PYE 05, 06
RADIOLA 05, 06
SABA 10
SALORA 26
SAMSUNG 31, 32
SANSUI 05, 31, 33
SANYO 21
SBR 06
SCHNEIDER 05, 06, 29, 30, 31
SELECO 06, 25
SHARP 18
SIEMENS 09
SINUDYNE 05, 06, 33
SONY 08
TELEFUNKEN 10, 11, 12, 13, 14
THOMSON 10, 15
TOSHIBA 16
WHITE WESTINGHOUSE 05, 06
Operation: Button
Numeric: [0-9,
TV aspect: [TV ASPECT]
TV/Teletext mode: [TV/TEXT]
Teletext: Colour buttons
The unit's remote control code
]
/