Page 1
ORDER NO.DSD0307011C7 DVD Video Recorder DMR-E100HP / DMR-E100HPC / DMR-E100HPL Colour (S).......Silver Type SPECIFICATIONS Specifications Power supply: AC120 V, 60 Hz Power consumption: 42 W Recording system: DVD video recording standards (DVD-RAM), DVD video standards (DVD- Optical pick-up: System with 1 lens, 2...
(Using built-in HDD): Max. 160 hours XP: 26 hours SP: 52 hours LP: 104 hours EP: 160 hours (HDD capacity 120GB) Region number: Region No.1 Discs played: 12 cm 4.7 GB DVD-RAM discs 12 cm 9.4 GB DVD-RAM discs 8 cm 2.8 GB DVD-RAM discs 12 cm 4.7 GB DVD-R discs (for General Ver.
Page 3
Input: LINE (pin jack) x3 Reference input: 309 mVrms FS: 2 Vrms (1 kHz, 0 dB) Input impedance: 47 k Output: LINE (pin jack) x2 Reference output: 309 mVrms FS: 2 Vrms (1 kHz, 0 dB) Output impedance: 1 k (Load impedance: 10 k Number of channels: Recording: 2 channels...
Page 4
BSD Video (MPEG2) *After VR conversion and transfer to HDD, the playback is possible. Card Slot: SD memory card Compatible Media: SD memory card, Multi media card, (SD slot only), Mobile HDD (PC slot only read only) Format: MPEG2 (SD-Video Entertainment Video Profile) (VR conversion and transfer to HDD only)
1. SAFETY PRECAUTIONS 1.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
measure the potential across the resistor. 4. Check each exposed metallic part, and measure the voltage at each point. 5. Reverse the AC plug in the AC outlet and repeat each of the above measurements. 6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current mu3st not exceed 1/ 2 milliamp.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparableconductive material).
( As shown in 15.2.1. The Main P.C.B. ) NOTE: The lithium battery is a critical component. ( Type No.: CR2032-1GUF Manufactured by Panasonic. ) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.
5. Handling the Lead-free Solder 5.1. About lead free solder (PbF) Distinction of PbF P.C.B.: P.C.B.s (manufactured) using lead free solder will have a PbF stamp on the P.C.B. Caution: - Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher.
Page 10
1. For details about the service / test modesetting mentioned in the description, refer to the “List of various modes”. - Service mode setting: While the power is off, press TIME SLIP, STOP, and OPEN / CLOSE simultaneously for five seconds. - Process mode 1 setting: While the power is off, press SKIP(R), TIME SLIP, and OPEN / CLOSE simultaneously for five seconds.
Page 11
6.2. Service Explorer in Detail 6.2.1. Does not operate items needed: RAM drive, digital P.C.B., remote control. Conditions: Nothing special.
Page 12
6.2.2. Poor Pictures Items needed: RAM drive, Digital P.C.B., RF cable, AV cable. Conditions: Check with TU IN-AV OUT(EE). When recording or playback is partially needed, follow the instructions.
Page 13
6.2.3. Other Items needed: Digital P.C.B., HDD. Conditions: Nothing special.
Page 14
6.2.4. Some defective functions Items needed: PC card adaptor (media), Digital P.C.B. conditions: Nothing special...
6.2.5. Caution when replacing the parts 1. RAM Drive In case the unit does not operate normally after replacement of the RAM Drive with new one. A. While power is off, press [SKIP (R)], [TIME SLIP] and [OPEN/ CLOSE] keys simultaneously for five seconds. Then the unit turns into “TEST Mode”, and the region code is stored on the new RAM Drive automatically.
Page 16
Procedure Item to Check Turn on the power. The Panasonic RAM disc should be recognized. Enter the EE (TU IN / AV IN - AV OUT) mode. No abnormality should be seen in the picture, sound or operation. Perform auto recording and playback for one No abnormality should be seen in the picture, minute using the RAM disc.
below. If the voltages are out of specification, adjust the voltages are in the specification as shown below. 8. Assembling and Disassembling 8.1. Disassembly flow chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing.
Page 18
8.2. P.C.B. Positions 8.3. The Top Cover 1. Remove the 2 screws (A) and 3 screws (B). 2. Open the both ends at the front side of the Top cover a bit and lift...
Page 19
the Top cover in the direction of the arrows. 8.4. The Front panel 1. Remove the 2 connectors. 2. Remove the 2 tabs (A) and 3 tabs (B) in this order. (The tab (A) and the tab (B) should be removed at the same time, respectively.) 3.
Page 20
8.5. The Front (R) P.C.B. 1. Remove the 2 screws and remove the Front Angle. 2. Remove the 4 screws (A) and remove the Front (R) P.C.B. 8.6. The Front (L) and DV Jack P.C.B. 1. Remove 1screw inside of the Front panel door with a precision screw driver.
Page 21
8.7. The SD & PC card P.C.B. 1. Remove the 4 screws. 2. Pull out the SD & PC card P.C.B. vertically. 8.8. The ATAPI and DRIVE-ATAPI P.C.B. 1. Remove the 2 screws. 2. Remove the FFC. CAUTION: When removing the FFC, pay attention as below.
Page 22
3. Remove the 2 connectors and remove the FFC. CAUTION: When removing the FFC, pay attention as below. 8.9. The Digital P.C.B.
Page 23
1. Remove the 3 screws and 4 tabs and remove the angle. 2. Pull out the Digital P.C.B. vertically with paying attention to 3 Connectors. 8.10. The DVD-RAM Drive 1. Remove the 2 connectors. 2. Remove the 3 screws and remove the 4 Tabs.
Page 24
CAUTION: When replacing the DVD-RAM drive, remove the tab as below. 8.11. HDD 1. Remove the screw (A) with angle and screw (B).
Page 25
2. Pull out the HDD holder vertically from Super sheet and HDD.
Page 26
Handling of HDD The following precautions should be taken when handling HDD. 1. Never give an impact to HDD. (Even a drop from 1cm height can be a cause of HDD failure. 2. When placing HDD on a workbench, provide a mat on a bench for shock absorption and anti-static purposes.
Page 27
8.12.1. In case of removing Fan motor from Rear panel 1. Remove the 2 screws. 2. Remove the 2 tabs. 8.13. The Power Supply P.C.B. and Main P.C.B. 1. Remove the 6 screws (A) and 2 screws (B). 2. Remove the HDD bracket and angle (A) and angle (B).
3. Remove the 2 connectors and 2 tabs (A). 4. Remove the Power Supply P.C.B and tab (B) , pull out it in the direction of the arrow. 5. Remove the 5 screws (B) and 2 tabs (C). 6. Remove the Main P.C.B. 9.
Page 29
2. Remove the SD & PC Card P.C.B. and angle. 3. Remove the FFC (ATAPI - Digital P.C.B.). 4. Remove the FFC (DRIVE ATAPI - Digital P.C.B.) 5. Remove the Digital P.C.B. 6. Use the extension cable (RFKZ0164) to connect the Main P.C.B. and Digital P.C.B.
Page 30
9.3. Checking the Main P.C.B. and FRONT (L), (R) P.C.B. 1. Remove the Top Cover. 2. Remove the Front Panel. 3. Remove the Rear Panel. 4. Remove the Power Supply P.C.B., Main P.C.B. and RAM Drive and HDD. 5. Use the extension cable (RFKZ0168) to connect the Main P.C.B. and Fan Motor.
Page 31
10. Use the extension cable (RFKZ0165) to connect the Main P.C.B. and Front (L) P.C.B. 11. Use the extension cable (RFKZ0166) to connect the Power supply P.C.B. and Front (R) P.C.B. Service tools Extension Cable RFKZ0165 (20pin) (Main P.C.B. - Front (L) P.C.B.) Extension Cable RFKZ0170 (19pin)
Page 32
9.4. Checking the Power Supply P.C.B. 1. Remove the Top Cover. 2. Remove the Front Panel. 3. Remove the screw which fixed Rear Panel and AC Inlet on the Power Supply P.C.B.. 4. Remove the HDD with HDD bracket. 5. Use the extension cable (RFKZ0169) to connect the HDD and Power supply P.C.B.
Page 33
9.5. Specifications for HDD Spin-up/Spin-down Condition of Working Spec. Indications Remarks Spin-up Spin- *When Recording or Playback *LED for HDD is ON for 5 seconds. down operation is not performed for *[LED SLEEP] is indicated on the over 30 minutes in condition that FL display.
Condition of Working Spec. Indications Remarks Spin-down Spin- The HDD shifts to Spin-up by HDD LED is on for about 5 Acceptation of operations shown below. seconds until the HDD starts to [REC] key in the spin. Spin-down *When the [HDD] key is pressed. condition is *When the playback operation permitted.
Page 35
Each buttons Functions name DIRECT DIRECT NAVIGATOR NAVIGATOR/ To display menu for recorded program. MENU <TOP MENU> (For only VCD or DVD-Video) To display top menu on the VCD or DVD-Video. Cursor buttons To move cursor position to select each menu. ENTER After selecting each menu with cursor buttons, press this...
Page 36
Each buttons Functions name TIME SLIP (HDD, RAM, DVD-R) To playback program being recorded by setting time duration for each 1minute during recording. (HDD, RAM, DVD-R) To playback recorded program by setting time duration for each 1minute. *During recording or playback, playback 30seconds previous by pressing the button.
Page 37
Item FL display Key operation Mode name Description Remote controller key Clear item Items 1-20 are cleared. [0] [0] while in service mode Error code display FL display of the last [0] [1] while in service mode error code held by timer ROM version display Region code, main, [0] [2] while in service mode...
Page 38
Item FL display Key operation Mode name Description Remote controller key RTSC return XP (A& Disc recording of L1 Initialization mode (EE2/ [1] [3] while in service mode input Encoded and Interlace/ XP/ Audio decoded for external 48kHz) output without playback.
Page 39
Item FL display Key operation Mode name Description Remote controller key Audio pattern output The audio pattern Initialization mode [2] [3] while in service mode stored in the internal (Interlace) memory is output (1kHz-18dB). Audio 44.1kHz / 48kHz [2] [4] while in white picture mode switched.
Page 40
Item FL display Key operation Mode name Description Remote controller key Factors which The disc condition is [4] [4] while in service mode cause drive error displayed when an error occures. Disc manufacture ID Display the [4] [5] while in service mode manufacture’s ID for a disc on which a drive error has occured.
Page 41
Item FL display Key operation Mode name Description Remote controller key Error code Initialization of the last [9] [8] while in service mode initialization error code held by timer (Write in F00) Main unit All parameters [9] [9] while in service mode initialization (including timer) are initiaized to the factory...
Item FL display Key operation Mode name Description Remote controller key SD card WRITE Check SD card WRITE When the WRITE check Insert SD card to SD card slot, check function with SD card is OK. and press [7] [4] in service mode. slot.
Page 43
Item FL display Key operation Mode name Description Front key Demonstration lock/ Ejection of the disc is With the power-on, press STOP unlock prohibited. and POWER simultaneously for five seconds. *When lock the tray: "LOCK" is displayed for 3 seconds. When unlock the tray: "UNLOCK"...
Page 44
Diagnosis Description FL display Display Remote control Display appears when main unit and remote mode error controller modes are not matched. Abnormal inner Display appears when the drive temperature temperature exceeds 71Åé. Main unit is powered off detected forcibly. For 30 minutes after this, all key entries are disabled.
Page 45
Diagnosis Description FL display Display Initialization error Display appears when initialization error is when main detected after starting up main microprocessor microprocessor for program recording. The is started up for event is saved in memory. program recording Remains displayed. Unsupported *A disc an unsupported format was played, UNSUPPORT disc error...
Page 46
10.3.3. Disk production maker ID * Since a display is arbitrarily set up by the disk producer side, the above-mentioned display may be changed. Please make it reference as an example of a display. 11. Abbreviations...
Page 47
INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMPOUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT BLACK DROP OUT...
Page 48
INITIAL/LOGO ABBREVIATIONS DACCK D/A CONVERTER CLOCK DEEMP DEEMPHASIS BIT ON/OFF DEMPH DEEMPHASIS SWITCHING DIG0~UP FL DIGIT OUTPUT DATA INPUT DMSRCK DM SERIAL DATA READ CLOCK DMUTE DIGITAL MUTE CONTROL DROP OUT DOUT0~UP DATAOUTPUT DATA SLICE RF (BIAS) DRPOUT DROP OUT SIGNAL DREQ DATA REQUEST DRESP...
Page 49
INITIAL/LOGO ABBREVIATIONS IECOUT IEC958 FORMAT DATA OUTPUT IPFRAG INTERPOLATION FLAG IREF I (CURRENT) REFERENCE ISEL INTERFACE MODE SELECT LDON LASER DIODE CONTROL LASER POWER CONTROL LRCK L CH/R CH DISTINCTION CLOCK MA0~UP MEMORY ADDRESS MEMORY CLOCK MCKI MEMORY CLOCK INPUT MCLK MEMORY SERIAL COMMAND CLOCK...
Page 50
INITIAL/LOGO ABBREVIATIONS READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK...
Page 51
SYSTEM CLOCK INITIAL/LOGO ABBREVIATIONS TRACKING ERROR TIBAL BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 TPSN OP AMP INPUT TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSSSIGNAL TRON TRACKING ON TRSON TRAVERSE SERVO ON INITIAL/LOGO ABBREVIATIONS VBLANK...
INITIAL/LOGO ABBREVIATIONS X' TAL XALE X ADDRESS LATCH ENABLE XAREQ X AUDIO DATA REQUEST XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XH INTERRUPTREQUEST X' TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE...
17. Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufactures specified parts shown in the parts list.
Page 58
FRONT ORNAMENT(R) 20-11 RGK1674-S FRONT ORNAMENT(L) 20-12 RKF0671-S TRAY DOOR 20-13 VMB3410 BLINDER SPRING 20-14 XTN2+6G SCREW 20-15 VGB0560 PANASONIC BADGE 20-16 RMC0577 DOOR SPRING 20-17 RGL0633-Q PANEL LIGHT 20-18 RYF0678A-S PANEL DOOR ASS’Y 20-19 XTBS26+8J SCREW 20-23 RGU2230-W DVD/HDD BUTTON...
Page 59
Ref. No. Part No. Part Name & Description Remarks 20-24 RMZ0724 PANEL SHEET 20-25 RMX0252 DAMPER SHEET RMC0549 EARTH PLATE XTBS26+10J SCREW REP3598AB FRONT (L) P.C.B. (RTL) REP3598BA FRONT (R) P.C.B. (RTL) REP3540CA SD CARD P.C.B. (RTL) 36-1 VXA7721 PC CARD SLOT 36-2 XYN2+F6 SCREW...
Page 60
Ref. No. Part No. Part Name & Description Remarks A6-3 RQCA1119 HDD CAUTION SHEET (P,PC) A6-4 RPF0378 POLYETHYLENE BAG(F.B.) (P,PC) A6-5 RQCA1121 PC CARD CAUTION SHEET (P,PC) RPQ1450 PAD(A) RPQ1594 PAD(C) RPG6593 PACKING CASE RPG6722 PACKING CASE (PC) RPG6723 PACKING CASE (PL) RPN1652A CUSHION(L)
svcdoc DVD Video Recorder 1 Specifications 1 1. SAFETY PRECAUTIONS 4 1.1. GENERAL GUIDELINES 5 1.1.1. LEAKAGE CURRENT COLD CHECK 5 1.1.2. LEAKAGE CURRENT HOT CHECK (See Figure 1 .) 5 2. PREVENTION OF ELECTRO STATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES 6 3.
Page 88
svcdoc 10.2.3. List of the U/H/F Error Displays 43 10.3. The information table of an error generating disk 45 10.3.1. Error generating disk type 45 10.3.2. Error generating disk state 45 10.3.3. Disk production maker ID 46 11. Abbreviations 46 12.
Page 89
svcdoc 15.2.4. Main P.C.B. ( Section 4/4 ) 54 15.2.5. Main P.C.B. Address Information 54 15.3. Digital P.C.B. 54 15.3.1. Digital P.C.B. ( Section 1/2 ) 54 15.3.2. Digital P.C.B. & DV Jack P.C.B. ( Section 2/2 ) 54 15.3.3. Digital P.C.B. Address Information 54 15.4.
Page 96
TO HDD DRIVE TO FP3502 P9801 DIGITAL P.C.B. (RTSC SECTION) P9802 RESET- RESET- DD10 DD10 DD11 DD11 DD12 DD12 DD13 DD13 DD14 DD14 DD15 DD15 DMARQ DMARQ DIOW- DIOW- DIOR- DIOR- IORDY IORDY DMACK- DMACK- INTRQ INTRQ DA0- CS0- DASP DASP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
IC Pin Terminal Chart (TC 1 - TC 6 ) IC Pin Terminal Chart (TC 7, TC 8, TC 9, TC 15, TC 16, TC 21, TC 22, TC 23 ) IC3203 / VAD CON IC3202 / V-PROCESSOR IC3402/AV ENC IC3202/V-PROCESSOR IC50003/AV DEC IC6004 / MAIN CPU...
Page 98
SD16 - SD31 DATA BUS LINE (TC20-2, TC17-2, TC19-2,TC35-2 ) IC Pin Terminal Chart (TC 28 - TC 32,TC34,TC37 ) 20-2 17-2 19-2 35-2 IC50003 / AV DEC IC37001 / DV DEC IC3608 / MPEG4 CODE IC3607 / SDRAM(32bit/16M) SIGNAL NAME SIGNAL NAME IC6004 / MAIN CPU IC6701 / GLUE...
Page 99
SA0 - SA25 ADDRESS BUS LINE (TC20-1, TC12-3, TC17-1, TC18, TC19-1, TC25, TC27,TC35-1) 20-1 12-3 17-1 19-1 35-1 IC6004/MAIN CPU IC3503 / RTSC IC6701/GLUE IC6007 / BUFFER IC6006 / LOADER IC50003 / AVDEC IC37001 / DV CODEC IC3608 / MPEG4 SIGNAL NAME Pin No Port Name...
Page 100
TO RAM DRIVE TO FP3501 P9801 DIGITAL P.C.B. (RTSC SECTION) P9802 RESET- RESET- DD10 DD10 DD11 DD11 DD12 DD12 DD13 DD13 DD14 DD14 DD15 DD15 DMARQ DMARQ DIOW- DIOW- DIOR- DIOR- IORDY IORDY DMACK- DMACK- INTRQ INTRQ DA0- CS0- DA1- CS1- NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 102
AUDIO EE SIGNAL IC4402 IC4403 IC6701 IC50010 (AUDIO BUFFER) (AUDIO ADC) (GLUE) (AUDIO DAC) PP9702 PS9002 AADCL MIX L OUT DM PS9002 PP9702 VINL VOUTL FROM MAIN P.C.B. DOUT AD IN2 AD OUT1 DATA (AUDIO SEC.) PP9702 PS9002 AADCR MIX R OUT DM PS9002 PP9702 VINR...
Page 103
OVER VIEW DIGITAL P.C.B. (1/2) DMR-E100H P/PC/PL (COMPONENT SIDE) DIGITAL P.C.B.(1/2) (REP3543E:P/REP3543EF:PC/REP3543EG:PL)
Page 104
DV JACK P.C.B. OVER VIEW DIGITAL P.C.B. (2/2) DMR-E100H P/PC/PL (FOIL SIDE) DV JACK P.C.B. (REP3540AB) DIGITAL P.C.B. (2/2) (REP3543E:P/REP3543EF:PC/REP3543EG:PL)
Page 105
DIGITAL P.C.B. Integrated Circuit CKA23 F CKC39 F CKF36 F CL3616 F CL37034 F FL3404 F FL50021 F C50016 F R3607 F R6013 C R37022 C R50054 C RX3617 F RX6711 IC3201 C CKA24 F CKC41 F CKF37 F CL3617 F CL37035 F FL3405 F FL50023...
Page 106
TO PP9701 MAIN P.C.B. (MAIN NET) PS9001 CPNCIN DM CPNCIN DM DGND CPSVIN DM V YIN DM CLAMP PULSE DGND CLAMP DC CLAMP PULSE Y GCA COUT CLAMP DC COUT DM Y GCA CONT YOUT DM DGND RPROUT DM COUT DM BPBOUT DM DGND GPYOUT DM...
Page 114
FRONT (L) P.C.B. DMR-E100H P/PC/PL FRONT (L) P.C.B. (REP3598AB) FRONT (R) P.C.B. DMR-E100H P/PC/PL FRONT (R) P.C.B. (REP3598BA)
Page 115
JK7001 K1U413A00006 FRONT A/V JACK C7003 R7002 TO P7501 MAIN P.C.B. (TIMER SECTION) P7001 CPN 2Y IN CPN 2C IN LINE 2V IN L2 C SDET R7008 R7009 R7010 C7004 L2 IN(L) 0.01 L2 IN(R) KEYIN3(R) KEYIN3(L) KEYIN2(R) KEYIN2(L) N SW 5V R7011 POWER S7003...
Page 116
TO PS103 POWER SUPPLY P.C.B. P7801 LED DVD LED REC DVD HDD LED LED WARP ON HDD REC LED KEYIN1 KEYIN2 KEYIN3 < X SW 5.15V > X SW 5.15V R7821 R7823 S7817 TIME-WARP PNA4618M13VT DVD REC D7801 B3ABA0000396 D7802 LNJ201LPQJA QR7801 UNR221400L...
Page 132
TU7401 ENGD6201D IIC DATA IIC CLK TO PS9003 UNREG38V DIGITAL P.C.B. R7419 R7418 C7417 C7416 D7401 (DIGITAL NET) 50V1 0.01 MAZ4300NMF PP9703 DGND JC REG5V 1 TUNER L CC LN21 TU VIDEO IN R7403 CC FIELD K7401 QR7401 ERJ3GEY0R00V CC LN21 R7405 R7452 UNR521300L...
Page 133
PSC 1. X SW+5.15V PSC 9. REG.D+1.5V PSC 10. D+3.3V PSC 11. REG.SD+1.8V Ref. No. Pin. No. Schematic Name Ref. No. Pin. No. Schematic Name Ref. No. Pin. No. Schematic Name Ref. No. Pin. No. Schematic Name IC7501 24,98 Timer (Main) IC50003 12,30,48 AV Decoder (Digital) IC3603...
Page 139
TO PP1501 MAIN P.C.B. (Sub Power Supply Sec.) PS105 D 1.8V D 1.8V D 3.3V D 3.3V L142 EXCELSA24 F101 X SW 5.15V 125V 2.5A X SW 5.9V L101 EXCELSA24 D101 RL2ZLF X SW 13V C129 R162 R163 L111 R142 C122 100P EXCELDR35...
Page 143
X SW 13V X SW 5.9V TO PS105 X SW 5.15V POWER SUPPLY P.C.B. PP1501 LB1501 J0JHC0000032 D 1.8V D 1.8V LB1502 J0JHC0000032 P:Sub Power Supply Section(Page: D 3.3V D 3.3V M:Main Net Section(Page: LB1503 J0JHC0000032 V:Video I/O Section(Page: X SW 5.15V LB1504 J0JHC0000032 A:Audio Main Section(Page: X SW 5.9V...
Page 144
DP7501 A2BD00000064 DISPLAY P:Sub Power Supply Section(Page: M:Main Net Section(Page: V:Video I/O Section(Page: A:Audio Main Section(Page: T:Timer Section(Page: TL7538 TL7501 KEYIN3 KEYIN2 R7567 TO P7001 R7568 FRONT(L)P.C.B. R7569 P7501 R7570 R7556 N SW 5V R7566 KEYIN2(L) R7571 KEYIN2(R) R7572 KEYIN3(L) R7573 KEYIN3(R) R7517...
Page 145
R7518 LB7508 G0ZZ00001936 D7502 C7525 C7526 C7524 R7519 IP7501 MAZ4240NMF 50V10 0.01 D4FAR4000001 X SW 13V T7501 ETS13TB119AP D7503 (POWER TRANS.) D7506 C7532 B0AAGM000007 MA2C18500E 35V47 LED HDD REC L7501 LED HDD 100u LED DVD C7529 R7588 6V220 LED REC DVD LED WARP ON C7531 POWER ON...
Page 146
AUDIO VIDEO AUDIO VIDEO LINE LINE LINE LINE LINE LINE LINE LINE IN(R) IN(R) IN(L) IN(L) L3 IN L1 IN CPN L3 IN CPN L1 IN OUT2(R) OUT1(R) OUT2(L) OUT1(L) OUT V2 OUT V1 CPN OUT2 CPN OUT1 JK3902 K1U820B00002 JK3901 A/V OUT JACK K1U822B00001...
Page 147
BLUE GREEN JK3903 K1U407B00003 DIGITAL AUDIO OUT LB4901 330 P:Sub Power Supply Section(Page: COMPONENT VIDEO OUT (525P/525I) M:Main Net Section(Page: GND VCC IN V:Video I/O Section(Page: LB4902 J0JGC0000020 A:Audio Main Section(Page: C4905 T:Timer Section(Page: IC4901 C0JBAB000173 (DIGITAL AUDIO OUT) C4904 C4903 R4903 0 6.3V47...
Page 149
PS9001 Ref No. MODE PLAY STOP PS9001 Ref No. MODE PLAY STOP PS9002 Ref No. MODE PLAY STOP PS9002 Ref No. MODE PLAY STOP PS9003 Ref No. MODE PLAY STOP Ref No. PS9003 MODE PLAY STOP...
Page 150
IC3005 :REC SIGNAL :PB SIGNAL (VIDEO DRIVER) VIDEO MUTE FROM CTRAP MUTE1 IC7501- 8 TIMER JK3902 MUTE2 Q3001 A/V OUT PS9001 PP9701 C OUT DM 1.5-6M COUT CPN C OUT JACK 75Ω MIXOUT CPS V OUT VIDEO1 75Ω LINE OUT VIDEO2 Q3002 PS9001 PP9701...
Page 151
:REC SIGNAL :PB SIGNAL IC6701 (GLUE) IC4002 TU7401 (AUDIO CH SELECTOR SW) U/V TUNER PACK QR4010 TUNER L A.SEL1 SW A IN SEL1 PP9702 PS9002 L OUT 27 TUNER L A IN SEL1 ODATA10 TUNER R R OUT TUNER R QR4011 A.SEL0 SW A IN SEL0...
Page 153
POWER SUPPLY P.C.B. MAIN P.C.B. D+1.8V PS105 PP1501 POWER TRANSFORMER AC SOCKET DC-DC CIRCUIT D+3.3V PS105 PP1501 SURGE RECTIFIER SUPPRESSOR REG. D+1.8V SURGE ABSORBER REG. D+3.3V IP101 Q108 POWER ON H PS105 PP1501 Q109 (CONSTANT VOLTAGE CTL.) X SW+5.9V PS105 PP1501 0 CURRENT DRAIN DET.
Page 164
TO PP1501 MAIN P.C.B. (Sub Power Supply Sec.) PS105 D 1.8V D 1.8V D 3.3V D 3.3V X SW 5.15V F101 125V 2.5A X SW 5.9V X SW 13V POWER ON P SAVE JC DR P ON TO PP1503 MAIN P.C.B. (Sub Power Supply Sec.) PS102 D125...
Page 165
14.3. Sub Power Supply Schematic Diagram (P) ( Main P.C.B. 1/5 ) TO PS105 POWER SUPPLY P.C.B. PP1501 LB1501 J0JHC0000032 D 1.8V D 1.8V LB1502 J0JHC0000032 D 3.3V D 3.3V LB1503 J0JHC0000032 X SW 5.15V LB1504 J0JHC0000032 X SW 5.9V LB1505 J0JHC0000032 X SW 13V POWER ON...
DMR-E100HP / DMR-E100HPC / DMR-E1 X SW 13V X SW 5.9V X SW 5.15V P:Sub Power Supply Section(Page: M:Main Net Section(Page: V:Video I/O Section(Page: A:Audio Main Section(Page: T:Timer Section(Page: JC REG 5V D 2.5V IC1509 C0DBZFG00012 (REG.D +2.5V) C1518 25V47...
Page 167
DMR-E100HP / DMR-E100HPC / DMR-E100HPL 14.4. Main Net Schematic Diagram (M) ( Main P.C.B. 2/5 ) IIC DATA IIC CLK TO PS9003 DIGITAL P.C.B. (DIGITAL NET) PP9703 DGND JC R CC LN21 TU V CC FIELD QR7401 CC LN21 R7405...
TU7401 ENGD6201D UNREG38V R7419 R7418 C7417 C7416 D7401 50V1 0.01 MAZ4300NMF JC REG5V 1 TUNER L TU VIDEO IN R7403 K7401 ERJ3GEY0R00V R7452 R7404 LB7402 J0JHC0000032 REG 5V C7405 C7404 6.3V47 0.01 IF OUT IF IN LB7403 J0JHC0000032 REG 5V C7412 C7411 LB7408...
Page 169
14.5. Video I/O Schematic Diagram (V) ( Main P.C.B. 3/5 ) AUDIO VIDEO LINE LINE IN(R) IN(R) IN(L) IN(L) L3 IN L1 IN CPN L3 IN JK3901 K1U822B00001 EXTERNAL A/V IN JACK IIC CLK IIC DATA TU VIDEO IN R3017 CLAMP PULSE CLAMP DC Y GCA CONT...
DMR-E100HP / DMR-E100HPC / DMR-E1 AUDIO VIDEO LINE LINE LINE LINE LINE LINE L3 IN CPN L1 IN OUT2(R) OUT1(R) OUT2(L) OUT1(L) OUT V2 OUT V1 CPN OUT2 CPN OUT1 JK3902 K1U820B00002 A/V OUT JACK R3018 R3924 R3922 R3908 R3907...
Page 171
DMR-E100HP / DMR-E100HPC / DMR-E100HPL BLUE GREEN JK3903 K1U407B00003 DIGITAL AUDIO OUT COMPONENT VIDEO OUT (525P/525I) GND VCC IN C4904 C4903 6.3V47 R3920 R3926 R3927 L4901 ANA 5V R3108 C4902 C4901 6.3V47 L3003 C3012 C3017 C3008 C3009 R3007 0.01 0.01 0.01...
Page 172
LB4901 330 P:Sub Power Supply Section(Page: M:Main Net Section(Page: V:Video I/O Section(Page: LB4902 J0JGC0000020 A:Audio Main Section(Page: T:Timer Section(Page: C4905 IC4901 C0JBAB000173 (DIGITAL AUDIO OUT) R4903 0 IECOUT L1 IN L L3 IN L L1 IN R L3 IN R R3084 9.1K R3085...
Page 173
14.6. Audio Schematic Diagram (A) ( Main P.C.B. 4/5 ) AU +9 C4037 50V10 R4052 68K L1 IN L C4038 50V10 R4053 68K L3 IN L C4039 50V10 R4054 68K L2 IN L R4013 18K C4043 0.1 C4028 R4037 R4040 R4042 180K 180K...
TL7538 R7567 R7568 R7569 R7570 R7556 R7566 R7571 R7572 R7573 R7517 VWJ0023=5 SEG31 SEG32 SEG33 R7544 P SAVE L R7506 DVD LED H R7507 DVD REC LED H R7508 HDD LED2 H IC7501 C2BBGF000419 LED WARP ON H R7509 (TIMER) TEST2 H R7510 S RXD...
Page 178
DMR-E100HP / DMR-E100HPC / DMR-E1 IP7501 D4FAR4000001 X SW 13V D7506 C7532 MA2C18500E 35V47 LED HDD REC LED HDD LED DVD R7588 LED REC DVD LED WARP ON C7531 POWER ON 0.022 DR P ON JC P ON P SAVE...
Page 179
DMR-E100HP / DMR-E100HPC / DMR-E100HPL 14.8. Digital Net Schematic Diagram (DN) ( Digital P.C.B. 1/9 ) TO PP9701 MAIN P.C.B. (MAIN NET) PS9001 CPNCIN DM DGND V YIN DM DGND CLAMP PULSE CLAMP DC Y GCA CONT DGND COUT DM...
Page 180
CPNCIN DM CPSVIN DM CLAMP PULSE CLAMP DC Y GCA COUT COUT DM YOUT DM RPROUT DM BPBOUT DM GPYOUT DM I2C5DT I2C5CK SCURVE0 SCURVE1 C GCA CONT AU5V AUGND XDMUTE XRESET MIXLOUT DM MIXROUT DM IECOUT AADC R AADC L ASEL0 ASEL1 D1.8V...
DMR-E100HP / DMR-E100HPC / DMR-E100HPL 14.17. ATAPI Schematic Diagram TO HDD DRIVE P9801 RESET- DD10 DD11 DD12 DD13 DD14 DD15 DMARQ DIOW- DIOR- IORDY DMACK- INTRQ DA0- DASP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORD...
Page 220
TO FP3502 DIGITAL P.C.B. (RTSC SECTION) P9802 RESET- DD10 DD11 DD12 DD13 DD14 DD15 DMARQ DIOW- DIOR- IORDY DMACK- INTRQ CS0- DASP DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN NT OR AMENDED SINCE THIS DRAWING WAS PREPARED. DMR-E100H P/PC/PL ATAPI Schematic Diagram...
Page 221
14.18. Drive ATAPI Schematic Diagram TO RAM DRIVE P9801 RESET- DD10 DD11 DD12 DD13 DD14 DD15 DMARQ DIOW- DIOR- IORDY DMACK- INTRQ DA0- DA1- NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAW IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR...
Page 222
DMR-E100HP / DMR-E100HPC / DMR-E1 TO FP3501 DIGITAL P.C.B. (RTSC SECTION) P9802 RESET- DD10 DD11 DD12 DD13 DD14 DD15 DMARQ DIOW- DIOR- IORDY DMACK- INTRQ CS0- CS1- OWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN HTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 227
DMR-E100HP / DMR-E100HPC / DMR-E100HPL 14.20. Front (L) Schematic Diagram TO P7501 MAIN P.C.B. (TIMER SECTION) P7001 CPN 2Y IN CPN 2C IN LINE 2V IN L2 C SDET L2 IN(L) L2 IN(R) KEYIN3(R) KEYIN3(L) KEYIN2(R) KEYIN2(L) N SW 5V...
Page 228
JK7001 K1U413A00006 FRONT A/V JACK C7003 R7002 R7008 R7009 R7010 C7004 0.01 USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. RECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-E100H P/PC/PL Y DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Front(L) Schematic Diagram...
14.21. Front (R) Schematic Diagram TO PS103 POWER SUPPLY P.C.B. P7801 LED DVD LED REC DVD HDD LED LED WARP ON HDD REC LED KEYIN1 KEYIN2 KEYIN3 < X SW X SW 5.15V R7821 TIME-WARP D7801 B3ABA0000396 QR7801 UNR22140 (TIME-WARP CH-UP SKIP-F R7801...
Page 230
DMR-E100HP / DMR-E100HPC / DMR-E1 < X SW 5.15V > R7823 S7817 PNA4618M13VT DVD REC D7802 LNJ201LPQJA QR7801 UNR221400L QR7803 (TIME-WARP LED DRIVE) UNR221400L (DVD REC LED DRIVE) R7822 QR7802 UNR221400L (DVD LED DRIVE) R7825 HDD REC S7818 K0H1BA000372 D7804...