Step 4 Set Up To Match Your Tv And Remote Control; Selecting Tv Type; Tv Operation; When Other Panasonic Products Respond To This Remote Control - Panasonic DMR-E75VS Operating Instructions Manual

Before Use

STEP 4 Set up to match your TV and remote control

∫ Selecting TV type

You do not have to change the setting when connected to a 4:3
standard aspect TV that is not compatible with progressive output.
(l 63)
Preparation
≥Press [DVD].
[1]
While stopped
Press [FUNCTIONS].
[2] Select "SETUP" with [3, 4, 2, 1] and press
[ENTER].
[3] Select "TV Screen" with [3, 4] and press
[2, 1].
Select "TV Type" with [3, 4] and press
[4]
[ENTER].
TV Type
SETUP
Aspect 4:3 & 480I
Aspect 4:3 & 480P
Channel
Aspect 16:9 & 480I
Set Up
Aspect 16:9 & 480P
Disc
Video
Audio
Display
TV Screen
≥Aspect 4:3/Aspect 16:9:
4:3
4:3 standard aspect TV
≥480P/480I:
Select "480P" if the TV is compatible with progressive output.
[5] Use [3, 4] to select the item and press
[ENTER].

∫ TV operation

You can configure the remote control TV operation buttons to turn
the TV on/off, change the TV input mode, select the TV channel and
change the TV volume.
Point the remote control at the TV
While pressing [Í POWER TV], enter the code
using the numeric buttons.
e.g., 01: press [0] ) [1].
Manufacturer and Code No.
Panasonic
National 01, 02
QUASAR
FISHER 10
GE 05
GOLDSTAR 15, 16, 17
HITACHI 12
JVC 11
LG 15, 16, 17
MAGNAVOX 03
MITSUBISHI 13
Test by turning on the TV and changing channels. Repeat the
procedure until you find the code that allows correct operation.
≥If your TV brand is not listed or if the code listed for your TV does
not allow control of your TV, this remote control is not compatible
with your TV.
(l 47)
16:9
16:9 widescreen TV
PHILIPS (RC-5) 03
RCA 05
SAMSUNG 14, 18, 19
SANYO 10
SHARP 06, 07
SONY 08
SYLVANIA 03
THOMSON 05
TOSHIBA 09
ZENITH 04
∫ When other Panasonic products respond
to this remote control
Change the remote control code on the main unit and on the remote
control (the two must match) if you place other Panasonic products
close together.
Use "1", the factory set code, under normal circumstances.
Preparation
≥Press [DVD].
[1]
While stopped
Press [FUNCTIONS].
[2] Select "SETUP" with [3, 4, 2, 1] and press
[ENTER].
[3] Select "Set Up" with [3, 4] and press [2, 1].
[4] Select "Remote Control Code" with [3, 4] and
press [ENTER].
[5] Use [3, 4] to select the code (1, 2, or 3) and
press [ENTER].
The code on the unit has been set.
[6]
While pressing [ENTER], press and hold for
about 2 seconds the numeric button ([1], [2] or
[3]) corresponding to the code you selected in
step 5.
The code on the remote control has been set.
[7]
Press [ENTER].
∫ When the following indicator appears on the unit's
display
The unit's remote control code
Change the code on the remote control to match the main unit's
(l step 6).
∫ To return to the previous screen
Press [RETURN].
∫ When you are finished
Press [RETURN].
17
(l 47)