User Settings; What Are The Settings You Need; Entering The User Settings Menu - Visonic PowerMax Complete User Manual

7. User Settings

What are the Settings You Need?

The installer provides you a ready-to-use alarm
system, but a few settings and adjustments will still
be needed.
Note: Although the
responsibility, you may request your installer to
perform them for you (except for the user codes,
which you would like to keep secret).
The user settings include (if enabled by the installer):
•
Bypassing zones - determining which zones
will be bypassed (disabled) during the present
disarm period and the next armed period.
•
Reviewing the bypass list - "show bypass" -
displaying the numbers and names of bypassed
zone one by one.
•
Recalling the last bypassing scheme** -
"recall bypass" - re-using the previous bypassing
scheme, which
disarming but
PowerMaxComplete memory.
•
Private report* - determining the event groups
to be reported to private telephone subscribers.
Determining the 1
numbers to which the system will report event
messages that were defined by the system
installer. Determining the 1
SMS telephone numbers to which pre-selected
event types will be reported.
•
Setting user codes* - programming a security
code for yourself and additional 7 codes for
other system users. Codes 5 through 8 are
"Latchkey" user codes (see Chapter 2 - Arming
in the Latchkey Mode for additional details).
•
Enrolling keyfob transmitters* - teaching the
PowerMaxComplete system to recognize the ID
code of each keyfob transmitter (multi-button,
Code-Secure™ type, wireless transmitter), so
that the PowerMaxComplete can respond to
commands transmitted by them.
•
Enrolling proximity tags - Teaching the
PowerMaxComplete to recognize the ID of each
proximity tag so that the PowerMaxComplete
can respond to proximity tags presentation.
•
Setting voice options* (not applicable in
PowerMaxComplete that does not have VOICE
feature) - Enabling
announcements (prompts).
•
Auto arm option* - enabling or disabling
automatic arming (at a predefined time).
•
Setting auto arm time - selecting automatic
arming time.
•
Using squawk option* - enabling/disabling
LOW/MID/HI squawk (short siren sound) upon
arming and disarming. All the options are
D-302213
user settings are
becomes suspended
is still saved in
st nd rd th
, 2 , 3 and 4 telephone
st nd rd
, 2 , 3 and 4
or disabling
applicable for wireless siren. For wired siren, refer
to LOW, MID and HI options as "squawk enable".
•
Setting the time and time format* - adjusting
the built-in clock to show the correct time and
time format.
your
•
Setting the date and date format* - adjusting
the built-in calendar date and date format.
•
Setting the scheduler* - setting schedule for
devices start/stop activation.
*
This option can be accessed only if master user
code has been entered.
**
This menu is not available when Partition is
enabled.

Entering the User Settings Menu

Figure 7 describes how to enter User Settings menu
(when all zones/partitions are secured) for the
Partition and non-Partition system.
after
the
Instruction: Enter 4-digit master
user code (default "1111"), or
user code (see note below).
These menu items are displayed
th
only if "bypass" was enabled by
the installer.
RECALL BYPASS is applicable
in Non-Partition menu only.
* Menu items that are marked
with an asterisk can be
accessed only if master
user code has been entered.
** This menu is not available
when Partition is enabled
***INSTALLER MODE is
displayed only if USER
PERMIT ENABLE was
selected by the installer.
verbal
Figure 7 - Entering User Settings Menu
The next paragraphs include User Settings instructions,
step-by-step. However, if you want to get an overall
view of the entire User Settings menu, refer to figure 8 -
User Setting flow-chart. You can use the flow chart as
your only guide along the user settings process, instead
of going through the step-by-step instructions.
USER SETTINGS
READY 00:00
WALK TEST
USER SETTINGS
ENTER CODE _ _ _ _
[master/ user code]
SET BYPASS
SHOW BYPASS
(**)
RECALL BYPASS
(*)
PRIVATE REPORT
(*)
SET USER CODES
(*)
ENROLL KEYFOB
(*)
ENROLL PROX TAG
(*)
SET VOICE OPTION
(*) (**)
AUTO ARM OPTION
(*)(**)
AUTO ARM TIME
(*)
SQUAWK OPTION
(*)
SET TIME&FORMAT
(*)
SET DATE&FORMAT
(*)
SCHEDULER
(*) (***)
INSTALLER MODE
<OK> TO EXIT
23