User Settings; What Are The Settings You Need; Entering The User Settings Menu - Visonic PowerMax User Manual

7. USER SETTINGS

What are the Settings You Need?

The installer provides you a ready-to-use alarm
system, but a few settings and adjustments will still
be needed.
Note: Although the
responsibility, you may request your installer to
perform them for you (except for the user codes,
which you would like to keep secret).
The user settings include:
•
Bypassing zones - determining which zones
will be bypassed (disabled) during the present
disarm period and the next armed period.
•
Reviewing the bypass list - "show bypass" -
displaying the numbers and names of bypassed
zone one by one.
•
Recalling the last bypassing scheme - "recall
bypass" - re-using the previous bypassing
scheme, which
disarming but is still saved in the PowerMax+
memory.
•
Programming the 4 telephone numbers* -
determining the 1st, 2nd, 3rd and 4th telephone
numbers to which the system will report event
messages that were defined by the system
installer.
•
Setting user codes* - programming a security
code for yourself and additional 7 codes for
other system users. Codes 5 through 8 are
"Latchkey" user codes (see Chapter 2 - Arming
in the Latchkey Mode for additional details).
•
Enrolling keyfob transmitters* - teaching the
PowerMax+ system to recognize the ID code of
each keyfob
SecureCode type, wireless transmitter), so that
the PowerMax+ can respond to commands
transmitted by them.
•
Setting voice options* - Enabling or disabling
verbal announcements (prompts).
•
Auto arm option* - enabling or disabling
automatic arming (at a predefined time).
•
Setting auto arm time - selecting automatic
arming time.
•
Using squawk option* - enabling/disabling
LOW/MID/HI squawk (short siren sound) upon
arming and disarming. All the options are
applicable for wireless siren. For wired siren,
refer to LOW, MID and HI options as "squawk
enable".
•
Setting the time and time format* - adjusting
the built-in clock to show the correct time and
time format.
DE5467U
user settings are
becomes suspended
transmitter (multi-button,
•
Setting the date and date format* - adjusting
the built-in calendar date and date format.
•
Setting the scheduler* - setting schedule for
devices start/stop activation.
* This option can be accessed only if master user
your
code has been entered.

Entering the User Settings Menu

Figure 7 describes how to enter the User Settings
menu.
Display in disarm state when all
zones are secured ("00:00 or
other digits show present time).
Instruction: click <NEXT> key
Instruction: Enter 4-digit master
after
user code (default "1111"), or
user code (see note below).
These menu items are displayed
only if "bypass" was enabled by
the installer.
* Menu items that are marked
with an asterisk can be
accessed only if master
user code has been entered.
** INSTALLER MODE is
displayed only if USER
PERMIT ENABLE was
selected by the installer.
Figure 7 - Entering User Settings Menu
The next
instructions, step-by-step. However, if you want to get
an overall view of the entire User Settings menu, refer
to figure 8 - User Setting flow-chart. You can use the
flow chart as your only guide along the user settings
process, instead of going through the step-by-step
instructions.
USER SETTINGS
1
2
3
Resultant display
ENTER CODE _ _ _ _
4
(*)
SET PHONE NUMBER
(*)
SET USER CODES
(*)
(*)
SET VOICE OPTION
(*)
AUTO ARM OPTION
(*)
(*)
(*)
SET TIME&FORMAT
(*)
SET DATE&FORMAT
(*)
(*) (**)
paragraphs include
READY 00:00
NEXT
NORMAL MODE
NEXT
USER SETTINGS
OK
[master/ user code]
SET BYPASS
NEXT
SHOW BYPASS
NEXT
RECALL BYPASS
NEXT
NEXT
NEXT
ENROLL KEYFOB
NEXT
NEXT
NEXT
AUTO ARM TIME
NEXT
SQUAWK OPTION
NEXT
NEXT
NEXT
SCHEDULER
NEXT
INSTALLER MODE
NEXT
<OK> TO EXIT
User Settings
23