Table of Contents
Advertisement
input, RF analyzer, 90,
421
input, spectrum analyzer,
manual control, 90, 421,
461
attenuator
decoder interference, 103,
input, 90, 421,
461
oscilloscope interference, 103,
attenuator hold, 291, 434,
444
Audio Analyzer Screen
AM Depth, 99,
419
Audio Frequency Analyzer screen
Distortion,
100
audio frequency counter
gate time,
98
sampling,
98
audio frequency generator,
audio frequency measurements, 59, 98,
106, 289, 424, 436, 446,
AUDIO IN connector
avoiding damage to,
509
description,
509
for ac level measurement, 97, 431,
for ac level measurements,
for call processing,
116
for external load resistancemeasure-
ment, 102,
444
for SNR operation, 98, 106, 289, 436,
446,
499
AUDIO IN HI connector,
509
Audio In Lo
AF Analyzer screen,
99
AUDIO IN LO connector
600 ohm impedance, 99,
floating, 99,
509
grounded, 99,
509
AUDIO MONITOR OUTPUT connector
description,
510
Audio Out
Duplex Test screen,
292
RF Generator screen,
434
Signaling Encoder screen, AMPS-
TACS mode,
302
Signaling Encoder screen, CDCSS
mode,
315
Signaling Encoder screen, Digi Page
mode,
320
Signaling Encoder screen, DTMF
mode,
325
Signaling Encoder screen, EDACS
461
mode,
Signaling Encoder screen, Func Gen
mode,
421
Signaling Encoder screen, LTR mode,
343
Signaling Encoder screen, NAMP-
421
NTAC mode,
Signaling Encoder screen, NMT mode,
370
Signaling Encoder screen, Tone Seq
mode,
AUDIO OUT connector
coupling, 292, 302, 315, 320, 325, 329,
340, 343, 370, 378,
442
description,
audio power
499
measurement, 97, 431,
audio source, 218, 226, 231, 235, 241,
247, 251, 263,
Auto All
442
Range Hold,
59
Auto/Norm
Oscilloscope screen,
automatic level control,
autoranging
AF/RF measurements,
gain setting,
input attenuator, 103,
Autostart Test Procedure on Power-Up
Tests (ExecutionConditions) screen,
482
509
auto-tuning
AF/RF measurements,
RF, 92, 297, 425,
averaging
example,
measurement results,
restart averaging,
AVG, 69,
329
340
302
378
434
510
442
281
208
396
107
208
103
421
208
504
69
69
69
527
B
B/I Delay (FOCC)
Signaling Encoder screen, AMPS-
TACS mode,
303
Signaling Encoder screen, NAMP-
NTAC mode,
303
backspace key,
529
bandwidth
adjacent channel power,
88
IF filter, 295, 421,
502
resolution, ACP measurement,
Base Freq
Configure screen,
203
base settings
changing,
74
default,
74
base station receiver
simulating,
AMPS-TACS/NAMPS-
NTACS,
217
basic operation,
53
Batt Save
Signaling Encoder screen, NMT mode,
370
battery,
51
saving,
370
baud rate,
387
beat frequency,
62
Beeper
Configure screen, 51,
204
beeper
error alert,
204
volume control, 51,
204
Bell
radio standard,
326
bias
dc, offsetting,
434
billing information,
375
bit error,
320
bits
CDCSS data rate,
227
CDCSS data stream,
318
CDCSS sequence,
227
digitial paging data rate,
232
dotting, 306,
308
information, 306,
308
LTR data rate,
252
message,
225
NMT data rate,
371
Index
92
567
Advertisement
Table of Contents
