Table of Contents
Advertisement
mkboot(1M)
NAME
mkboot, rmboot - install, update or remove boot programs from disk
SYNOPSIS
/usr/sbin/mkboot
[
preserved_lif_file] [
-p
/usr/sbin/mkboot
/usr/sbin/mkboot -e
/usr/sbin/rmboot
DESCRIPTION
is used to install or update boot programs on the specified device file.
mkboot
The position on device at which boot programs are installed depends on the disk layout of the device.
examines device to discover the current layout and uses this as the default. If the disk is unini-
mkboot
tialized, the default is LVM layout on PA-RISC and Whole Disk on Itanium(R)-based systems. The default
can be overridden by the
Boot programs are stored in the boot area in Logical Interchange Format (LIF), which is similar to a file
system. For a device to be bootable, the LIF volume on that device must contain at least the
tial system loader) and
physical volume, the
LABEL
For the VERITAS Volume Manager (VxVM) layout on the Itanium-based system architecture, the only
relevant LIF file is the
system boots to determine the location of the root, stand, swap, and dump volumes.
Options
mkboot
recognizes the following options:
-a
auto_file_string
boot_file_path
-b
-c
-e
-f
HP-UX 11i Version 2: December 2007 Update
[
-b
boot_file_path] [
-c
[
-u
|
|
] [
-l
-H
-W
-v
[
-a
auto_file_string] [
-v
] device
[
-l
] [
-s
efi_file_path] [
device
-l
,
-H
, or
-W
options.
(the HP-UX bootstrap utility) LIF files. If, in addition, the device is an LVM
HPUX
file must be present (see lvlnboot(1M) ).
LABEL
file. All other LIF files are ignored. VxVM uses the
If the
-a
option is specified,
device, if none exists.
string contains spaces, it must be quoted so that it is a single parameter.
If this option is given, boot programs in the pathname specified by
boot_file_path are installed on the given device.
If this option is specified,
sufficient for the boot programs. If the
checks if each included_lif_file is present in the boot programs. If the
option is specified, it checks if each preserved_lif_file is present on the dev-
ice. If all these checks succeed,
of these checks fail,
option is also selected, a message is also displayed on the standard output.
Use Itanium-based system EFI layout. This option causes
EFI utilities from
/usr/lib/efi
idisk(1M) and efi(4). This option is applicable only on Itanium-based
machines; it may not be used on PA-RISC. (Use the
non-default source for EFI files.)
This option forces the information contained in the boot programs to be
placed on the specified device without regard to the current swapping status.
Its intended use is to allow the boot area to grow without having to boot the
system twice (see
-h
This option should only be used when the system is in the single user state.
This could be a dangerous operation because swap space that is already allo-
cated and possibly in use will be overwritten by the new boot program infor-
mation. A message is also displayed to the standard output stating that the
operator should immediately reboot the system to avoid system corruption
and to reflect new information on the running system.
A safer method for reapportioning space is to use the
− 1 −
] |
-f
|
-h
|
-u
] [
-i
] device
-v
] [
-W
] device
mkboot
creates an autoexecute file
deposits auto_file_string in that file. If this
mkboot
checks if the available space on device is
mkboot
-i
option is also specified,
mkboot
exits with a status code of 0. If any
exits with a status code of 1. If the verbose
mkboot
to the EFI partition on the disk; see
option).
Hewlett-Packard Company
mkboot(1M)
included_lif_file]
(the ini-
ISL
LABEL
file when the
AUTO
on
mkboot
-p
to copy
mkboot
option to specify a
-s
-h
option.
561
m
Advertisement
Table of Contents
