Hitachi SJ7002 Series Instruction Manual page 144

3–60
"C" Group: Intelligent Terminal Functions
Func. Name/
Code Description
C038 Low current indication
output mode select
C039 Low current indication detection level
Low current threshold, used for intelligent output [LOC]
C040 Overload signal output mode ON
Choose when the overload
signal is enabled
C041 Overload level setting 1
C042 Frequency arrival setting for acceleration
Sets the frequency arrival setting threshold for the output frequency during acceleration
C043 Arrival frequency setting for deceleration
Sets the frequency arrival setting threshold for the output frequency during deceleration
C044 PID deviation level setting
Sets the PID loop error threshold |SP - PV| (absolute value) to trigger intelligent output [OD]
C045 Frequency arrival setting for acceleration (2)
C046 Frequency arrival setting for deceleration (2)
C052 Maximum PID feedback (PV) data
C053 Minimum PID feedback (PV) data
C055 Over-torque (forward-driving) level setting
Threshold for intelligent output terminal [OTQ], quadrant I
C056 Over-torque (reverse regenerating) level
setting
Threshold for intelligent output terminal [OTQ], quadrant II
C057 Over-torque (reverse driving) level setting
Threshold for intelligent output terminal [OTQ], quadrant III
C058 Over-torque (forward regenerating) level
setting
Threshold for intelligent output terminal [OTQ], quadrant IV
C061 Electronic thermal warning level setting
Sets the threshold for intelligent output [THM]
C062 Alarm code output
Allows binary alarm codes to
be output to intelligent
terminals
C063 Zero speed detection level
C064 Heatsink overheat warning level
Alarm temperature threshold for heatsink in inverter
Keypad
Range and Settings
SRW OPE
00
ON Output during acceleration/deceleration and
constant speed operation
0 1
CRT Output only during constant speed
0.0 to 1.80 x rated inverter current
00
During accel / decel / constant speed
0 1
During constant speed only
CRT
0.00 x rated current to 1.80 x rated current
(A)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.0 to 100.0 (%)
0.0 to 99.99, 100.0 to 400.0 (Hz)
0.0 to 99.99, 100.0 to 400.0 (Hz)
0.0 to 100.0 (%)
0.0 to 100.0 (%)
0. to 180. (%)
0. to 180. (%)
0. to 180. (%)
0. to 180. (%)
0. to 100. (%)
00
OFF Disable
0 1
3BIT Enable – 3-bit code
02
4BIT Enable – 4-bit code
0.00 to 99.99 / 100.0 (Hz)
0. to 200.0 (°C)
Defaults
Run
Mode
FEF2 FUF2 FF2
Edit
FE2 FU2 F2
Lo Hi
(EU) (USA) (Jpn)
✘ ✔
01 01 01
✘ ✔
Rated current x 1.0
✘ ✔
✘ ✔
01 01 01
✘ ✔
Rated current for
inverter
✘ ✔
0.00 0.00 0.00
✘ ✔
0.00 0.00 0.00
✘ ✔
3.0 3.0 3.0
✘ ✔
0.00 0.00 0.00
✘ ✔
0.00 0.00 0.00
✘ ✔
0.00 0.00 0.00
✘ ✔
100.0 100.0 100.0
✘ ✔
100. 100. 100.
✘ ✔
100. 100. 100.
✘ ✔
100. 100. 100.
✘ ✔
100. 100. 100.
✘ ✔
80. 80. 80.
✘ ✔
00 00 00
✘ ✔
0.00 0.00 0.00
✘ ✔
120 120 120
✘ ✔