Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Euphonix MixView CS3000
Summary of Contents for Euphonix MixView CS3000
- Page 1 CS3000 CS2000 MixView Software Supplement Version 3.2 Revision 3...
- Page 2 DSC, GainBall, GainCurve, TrackPanner and PanBall are trademarks of Euphonix Inc. ©1998 Euphonix Inc. All rights reserved worldwide. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without written permission of Euphonix Inc.
-
Page 3: Table Of Contents
TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS SECTION 1 : FADER ENHANCEMENTS ..... 1 - 3 Fader Names ..................1 - 3 Fader dB Level Displays ..............1 - 4 Fader Swap ................... 1 - 4 Backstop Pre Fader Listen (PFL) ............ - Page 4 This page intentionally left blank...
-
Page 5: Section 1 : Fader Enhancements
SnapShot and its associated fader names. By then setting SS:Off, recalling the desired destination SnapShot, then storing to it again, the displayed fader names will be added to the second SnapShot. Euphonix CS3000/2000 MixView 3.2 Software Supplement 1 - 3... -
Page 6: Fader Db Level Displays
For instance, if you want to make a touch-activated fader move on a channel’s non-motorized upper fader, Fader Swap allows you to “virtually” swap the physical faders of 1 - 4 Euphonix CS3000/2000 MixView 3.2 Software Supplement... -
Page 7: Backstop Pre Fader Listen (Pfl)
PFL bus. The standard PFL switch remains unaffected. This makes it AFL key still calls attention when possible to leave some channels in PFL while letting others only momentarily added but not when removed. enter PFL. Euphonix CS3000/2000 MixView 3.2 Software Supplement 1 - 5... - Page 8 Fader Solo Mstr Cnsl Meter MFdr BPFL Ext Solo Menu BPFL Menu Cnfg Diag Backup Backstop PFL : The console default is OFF . Press [F4] to set the feature ON. 1 - 6 Euphonix CS3000/2000 MixView 3.2 Software Supplement...
-
Page 9: Section 2: Monitoring Enhancements
In this example, Monitor A’s source selection parameters have been copied to Monitor B. Remember that the currently selected Monitor, (mA, mB or mC), determines which parameters are used for the group. Euphonix CS3000/2000 MixView 3.2 Software Supplement 1 - 7... -
Page 10: Monitor Level Linking
The second alpha character after the first arrow indicates the Level Linking status for the selected Monitor. A Monitor may only be linked to one other Monitor. Two Monitors may be linked to the same Master (i.e., A & B linked to 1 - 8 Euphonix CS3000/2000 MixView 3.2 Software Supplement... -
Page 11: Section 3: Snapshot Enhancements
Snapshots, thereby removing them from future Title Saves. Currently Active SnapShot RED, GREEN, or BLANK tags indicate whether or not a Snapshot will be stored with the Title on the next Title Save request. UNDO REDO BLANK Euphonix CS3000/2000 MixView 3.2 Software Supplement 1 - 9... -
Page 12: Merging Snapshot Lists
Mixview Platform. In the case of a Broadcast System an Uninteruptable Power Solution is recommended to ensure system performance. Con- tact Euphonix Customer Support for a list of tested UPS solutions. 1 - 10 Euphonix CS3000/2000 MixView 3.2 Software Supplement... -
Page 13: Section 4 : Misc Enhancements
Extension before clipping, standardizing the headroom between the console and the Dynamics modules. For information on this modification, please call Euphonix customer support. With a required hardware modification, the console’s Solo bus logic may be Multiple Console linked across multiple consoles. -
Page 14: Project Dates
SnapShot information. Breaking a link leaves each EQ in whatever state it was in at the time the link was removed. Copying linked EQs As before, only vertical EQ links can be copied between console channels. 1 - 12 Euphonix CS3000/2000 MixView 3.2 Software Supplement... -
Page 15: Automating Linked Eqs
The Skip event triggers playback to stop and locates the audio deck for the next stage cue. Timeline approaches cue #3 set to skip Timeline jumps to cue #4 after reaching cue #3 Euphonix CS3000/2000 MixView 3.2 Software Supplement 1 - 13... -
Page 16: The List Key
(the LIST key) or via the existing Locate menu system. Page 2 Page 3 Page 4 Page 1 List Chan LIST key immediately accesses the Cue List 1 - 14 Euphonix CS3000/2000 MixView 3.2 Software Supplement... -
Page 17: Section 5: Automation Enhancements
“on-the-fly” automated punch-in/out. Loop mode provides the Punch-in/out ability to capture timecode values on-the-fly. Build mode provides the capabil- ity to automatically set a punch-in marker at the timecode address where the last Pass was ended. Euphonix CS3000/2000 MixView 3.2 Software Supplement 1 - 15... -
Page 18: Loop Mode
Enable Enable Edit End Next Pass Overwrite Repeat Fill Zoom Full Prev Pass Gap INS Bounce Distribute Confirm Punch Group Enter Clear OVR Set Cue Set Mark Pass Control Keypad Template 1 - 16 Euphonix CS3000/2000 MixView 3.2 Software Supplement... -
Page 19: Build Mode
Pass Record Key. In a Television Post situation each of these functions will prove useful at different times. Experiment with each to discover how best they can work for you. Euphonix CS3000/2000 MixView 3.2 Software Supplement 1 - 17... -
Page 20: Automation Glide
CUBE Glides operate in the same manner as Desk Glides, except that CUBE CUBE Automation Glide Glide additionally supports the TRIM automation mode. 1 - 18 Euphonix CS3000/2000 MixView 3.2 Software Supplement... -
Page 21: Cube Aux Send Automation
In Abs mode, the “d” portion of the idt LEDs will light. In Trim i d t mode, the “t” LED will Red PanBall light and the associ- indicator ated DSC MixView screen knobs turn green. Euphonix CS3000/2000 MixView 3.2 Software Supplement 1 - 19... -
Page 22: All Punch And All Clear
Please refer to the CS3000 Manual for information on CUBE Setup. The following figure shows a one-per-channel CUBE setup: Panners 1-8 for channel #24 (Lower Fader Block only) are selected for edit operation Total Panners selected = 8 1 - 20 Euphonix CS3000/2000 MixView 3.2 Software Supplement... -
Page 23: Cutting Automation Moves
DSC [Pass Ctrl] key, [F4] (down arrows), Pass [F3] (Edit) and then [F4] (T/C): Ctrl Automation Pass 0 Undo? Redo? COPY? [Yes] Tplt Edit Menu Clr? Pack? Edit Util Start: 00:00:00.00 Start (green) (red) Euphonix CS3000/2000 MixView 3.2 Software Supplement 1 - 21... -
Page 24: Copying And Bouncing Automation Moves
Automation Edit Template to deselect the source data channel followed by the selection of the destination channels and the final Bounce operation. 1 - 22 Euphonix CS3000/2000 MixView 3.2 Software Supplement... -
Page 25: Enhanced Pass Control Show System
Section 2: Monitoring Enhancements The Euphonix TrackPanner I/O module, allows you to set the relative positions Track Panner of audio objects within the surround soundstage in a very natural manner using a trackball-style panning interface. Before the TrackPanner can be used, it must be activated. To activate the... - Page 26 P / S / Lv / Bm You can now use the SpinKnob or DSC [+]/[–] keys to select the Display Set you want. Press the DSC [Enter] key to complete the operation: Aux 5-8 1 - 24 Euphonix CS3000/2000 MixView 3.2 Software Supplement...
Need help?
Do you have a question about the MixView CS3000 and is the answer not in the manual?
Questions and answers