Tighten
four hex head bolts and lock washers
(Figure
9,
Nos. 4 and 10) very securely.
This procedure
will set the
table in parallel
position
and prevent
the table from shifting.
MOUNT
TABLE
EXTENSIONS
Refer to Figure
9, page
22.
Be certain
both edges
of table
(No. 1) and table extension
(No. 2) are clean and free from any preservative,
debris
or
burrs.
Attach
each table extension
with three
hex head bolts, lock
and flat washers
(Nos. 3, 4 and 29). Fasten
the hex head
bolts and lock washers
to matching
tapped
holes
in table.
Hand tighten.
Using
a straightedge,
set top of extension
flush with the
table top. Extension
should
also be centered
front to rear.
First, slightly
tighten
the center
bolt. If either
end is not
flush, tap extension
up or down with rubber
mallet.
Bring
extension
in line with table.
Securely
tighten
one bolt at a
time,
keeping
extension
flush with table top.
MOUNT
RIP
FENCE
RAILS
AND
EXTENSION
TABLE
Refer to Figures
9 and 10, pages
22 and 24.
Attach
rip fence front
rail (Fig. 10, No. 6) to front of table
(Fig. 9, No. 1). Rails will extend
out approximately
36" from
right
side of saw.
NOTE:
Front
rail is 2 x 2", rear rail is 1V2x 1Vz'.
Place
front rail, oriented
as shown
in Figure
10, against
the table and locate the holes
in the table. Fasten
rail to
table with pan head
screws
(Fig. 10, No. 7) and with
washers
and nuts (Fig. 10, Nos. 27, 28 and 29) on the
inside of the table. Finger
tighten
loosely. Tighten
securely
after all fasteners
have been
attached.
Place
rear rail (Fig. 10, No. 31), oriented
as shown
in
Figure
10, against
the table and locate the holes in the
table.
Place
hex head bolt (Fig. 10, No. 32) through
hole in
rail, through
spacer
(Fig. 10, No. 30), and then through
hole in table. Secure
with washers
and hex nut (Fig. 10,
Nos. 27, 28 and 29) inside
table.
Finger
tighten
loosely.
Tighten
securely
after all fasteners
have been
attached.
Attach
one 8mm
hex nut and foot to each
leg (Fig 10, Nos.
38, 39 and 42).
Attach
each
leg to the support
bar using two 8mm
hex
head
bolts and lock washers
(Fig. 10, Nos. 4, 5 and 41).
Set this assembly
aside.
Position
extension
table (Fig. 10, No. 40) between
the table
saw rails, with the holes in the table and rails aligned.
NOTE:
The notch
in the table should
be positioned
at the
right
side of the front rail. Use clamps
to secure
table or
have another
person
support
table.
Secure
extension
table to the front rail using two 8mm flat
head screws,
flat washers
and hex nuts (Fig. 10, Nos. 36, 37
and 38). Secure
the left side of the extension
table to the
rear rail using a 10x35mm
hex head bolt, flat washer
and
hex nut (Fig. 10, Nos. 32, 27 and 29). Secure
the right side
of the extension
table to the rear rail using a 10x70mm
hex
head
bolt, flat washer
and hex nut (Fig. 10, Nos. 35, 27 and
29).
Place
the guide
rail (Fig. 10, No. 2) on top of the front rail
at this time. Do not attach
scale to guide
rail at this time.
Place
a hex nut and flat washer
(Fig. 10, Nos. 27 and 29)
onto the 10x70mm
hex head
bolt. Position
the leg-support
bar assembled
previously
underneath
table and with the
10x70mm
hex head bolt through
the vertical
bend
of the
support
bar. Align
holes in the support
bar, front
rail and