Advertisement
MOTOR
SPECIFICATIONS
AND ELECTRICAL
REQUIREMENTS
This saw is designed to use a 3450 RPM motor only.
Do not use any motor that runs faster than 3450
RPM. It is wired for operation
on 110-120volts,
60
Hz.,
alternating
current.
IT
MUST
NOT
BE
CONVERTED
TO OPERATE ON 230 VOLTS.
CONNECTING
TO POWER SOURCE OUTLET
This saw must be grounded
while in use to protect
the operator from electrical
shock.
If power cord is worn or cut, or damaged in anyway,
have it replaced
immediately.
Your saw has a plug that looks like the one below.
3-PRONG
PLUG
<
GROUNDING
PRONG
_
PROPERLY
GROUNDED
3-PRONG
OUTLET
Plug power cord into 110-120V properly
grounded
type outlet
protected
by a 15-amp. time delay or
Circuit-Saver
fuse or circuit
breaker.
IF YOU ARE NOT SURE THAT YOUR OUTLET
IS
PROPERLY GROUNDED,
HAVE IT CHECKED
BY
A QUALIFIED
ELECTRICIAN.
WARNING:
DO
NOT
PERMIT
FINGERS
TO
TOUCH
THE
TERMINALS
OF
PLUG
WHEN
INSTALLING
OR REMOVING
THE PLUG TO OR
FROM THE OUTLET.
WARNING: IF NOT PROPERLY GROUNDED
THIS
POWER
TOOL
CAN
HAVE
THE
POTENTIAL
HAZARD OF ELECTRICAL
SHOCK, PARTICU-
LARLY
WHEN
USED" IN DAMP
LOCATIONS,
AROUND
PLUMBING,
OR OUT OF DOORS. IF AN
ELECTRICAL
SHOCK
OCCURS
THERE
IS THE
POTENTIAL
OF A SECONDARY
HAZARD SUCH
AS
YOUR
HANDS
CONTACTING
THE
SAWBLADE.
This saw is equipped
with a 3-conductor
cord and
grounding
type plug which has a grounding
prong,
approved
by Underwriter's
Laboratories
and the
Canadian
Standards
Association.
The
ground
conductor
has a green lug and is attached to the tool
housing at one end and to the ground prong in the
attachment
plug at the other end.
This plug requires a mating 3-conductor
grounded
type outlet as shown.
If the outlet you are planning to use for this saw is of
the two prong type DO NOT REMOVE OR ALTER
THE GROUNDING
PRONG IN ANY MANNER. Use
an adapter
as shown
and always
connect
the
grounding
lug to a known ground.
It is recommended
that
you
have a qualified
electrician
replace
the TWO prong outlet
with a
properly
grounded
THREE prong outlet.
An
adapter
as
shown
below
is
available
for
connecting
plugs
to 2-prong
receptacles.
The
green grounding
lug extended
from the adapter
must be connected
to a permanent
ground such as
to a properly
grounded
outlet box.
GROUNDING
LUG
_MAKE
SURE THIS IS
3-PRONG
_Y"7 _
I _'-'_.--.
CONNECTED
TO A
PLUG
_--_
_ [_"_,
II
KNOWN
GROUND
__
_
2-PRONG
l
RECEPTACLE
ADAPTER
NOTE: The adapter illustrated
is for use only if you
already
have
a
properly
grounded
2-prong
receptacle.
The use of any extension
cord will cause some loss
of power. To keep this to a minimum
and to prevent
over-heating
and motor
burn-out,
use the table
below to determine the minimum wire size (A.W.G.)
extension
cord.
Use only 3 wire extension
cords
which
have 3 prong
grounding
type plugs
and
3-pole receptacles.which
will accept the plug on the
saw.
1 H.P. MOTOR 110-120V
Extension Cord Length
Wire Size A.W.G.
Up to 50 Ft ..................
14
50 to 100 Ft ..................
12
100 - 200 Ft ..................
10
200 - 400 Ft ....................
8
CONTENTS
Warranty
....................................
2
General Safety Instructions
For Power Tools ...........................
2
Additional Safety Instructions
For Table Saw
.............................
3
Motor Specifications/_nd
Electrical Requirements
....................
5
Unpacking And Checking Contents
...........
6
Assembly ....................................
8
Getting To Know Your Saw ..................
22
Location And Function of
Electronic Controls
.....................
22
Location And Function of
Mechanical Controls
....................
23
Basic Saw Operation
........................
27
Calibrating The Saw For
Electronic Operations
...................
29
Recommended
Accessories
.................
40
Maintenance
................................
41
Lubrication
.................................
41
Trouble Shooting
...........................
42
Repair Parts
................................
46
Advertisement
