Table of Contents
Advertisement
SET UP FOR USE
You can program the tuner to scan only the channels you
receive in your area. You must use the remote control
for this procedure.
NOTES:
* Channel
memory
programming
is NOT
needed when connected to a cable box or satel-
lite box as in Fig 4 on page 11 or Fig 5 on
page12. In this case with your remote, select the
VCR to channel 3 or 4 the same channel as lo-
cated on the back ofVCR (CH3 or CH4). Then
the channel you wish to record or view may be
selected on the cable box or satellite box.
• Follow the steps below only when you plug the VCR
power cord into a standard AC outlet for tbe lust time.
If you unplug the VCR and move it to another area,
you need to "CHANNEL SET UP AGAIN" on page
16.
• You must follow the steps below before attempt-
ing to play or record a video tape. If you want to
play or record a video tape BEFORE program-
ming the tuner, you can cancel it by pressing the
RESET/EXIT button. To program the tuner again,
see "CHANNEL SET UP AGAIN" on page 16.
1
Plug in the VCR power cord
Plug the VCR power cord into a stand-
ard AC outlet. The "- - : - -" indicator
flashes on the display.
Remember:
If your cable box or satellite box is con-
nected as in Fig 4 on page 11 or Fig 5 on
page 12, you DO NOT have to set up the
channels. Just select the TV and VCR to
channel
3 or 4 and also have
the
CH3/CH4 switch on the back of the VCR
to match the channel you selected (CH 3
or CH 4). Now select the Box to the chan-
nel you wish to view or record.
2 Select channel 3 or 4 on the TV
I_
Turn on the TV and set the TV to channel 3
[Back of
or 4. Now set the CH3/CH4 switch on the
the VCR1
back of the VCR to matchthe channelselectedon the
TV.
3
Turn on the VCR
Press the POWER buttonto turn on theVCR. Both the
"PWR." indicator and the "VCR" indicator on the VCR
come on.
• Use the remote control for this procedure.
<_
4
Select "ENGLISH"
or "ESPAI_IOL"
Select
"ENGLISH"
or
"ESPAIqOL"=Spanish
by using
the PLAY/•
or STOP,_' button.
Then,
press
the MENU
or
F.FWD/_. button.
L*U_GUA_ SELECT
Note: This WILL NOT change the audio (sound) com-
ing out of the VCR only the screen menu.
5 Begin channel preset
[
c.0,1
Press the MENU, F.FWD/I_ or
% I /
REW/_I button once. The tuner
-- _.._u,_
scans and memorizes all active
/
I '_.
channels in your area.
• The VCR distinguishes between standard TV chan-
nels and cable channels.
6
After scanning
The tuner stops on the lowest
memorized
channel.
The TV
screen returns to TV mode.
CH 01
• If "TUNER SET UP" appears on the TV screen
again, check the cable connections. Press the MENU,
F.FWD/I_ or REW/_I button once again and the
VCR will begin preset again.
TO SELECT A DESIRED
CHANNEL
You can select the desired channel by using the CHAN-
NEL • or • button or directly pressing the number but-
tons on the remote control.
Note for using the number
buttons:
• When selecting
cable channels which are higher than
99, press the +100 button first, then press the last two
digits. (Example:
to select channel
125, first press the
+100 button then press "2" and "5").
• You must precede
single-digit
channel numbers
with
a zero (For example:
02, 03, 04 and so on).
- 14 -
EN
8F23
Advertisement
Table of Contents
