Table of Contents
Advertisement
SET UP FOR USE
You can program the tuner to scan only the channels you
receive in your area.
NOTES:
• Channel
memory
programming
is NOT
needed when connected to a cable box or satel-
lite box as in Fig 4 on page 11 or Fig 5 on
page12. In this case with your remote, select the
VCR to channel 3 or 4 the same channel as lo-
cated on the back ofVCR (CH3 or CH4). Then [
the channel you wish to record or view may be
selected on the cable box or satellite box.
• Follow the steps below once. Repeat it only if
there is a power failure or if the VCR is unplugged
for more than 30 seconds. (In these cases, the pro-
grarnmed channels arc erased.)
• You must follow the steps below before attempt-
ing to play or record a video tape. If you want to
play or record a video tape BEFORE
program-
ming the tuner, you can cancel it by pressing the
RESET/EXIT button. To program the tuner again,
see "CHANNEL
SET UP AGAIN"
on page 16.
1
Plug in the VCR power cord
Plug the VCR power cord into a stand-
ard AC outlet.
Remember:
If your cable box or satellite box is con-
nected as in Fig 4 on page 11 or Fig 5 on
page 12, you DO NOT have to set up the
channels. Just select the TV and VCR to
channel
3 or 4 and
also
have
the
CH3/CH4 switch on tile back of the VCR
to match the channel you selected (CH 3
or CH 4). Now select the Box to the chan-
nel you wish to view or record.
2
Select channel 3 or 4 on the "IV
Turn on the TV and set the TV to channel 3
or 4. Now set the CH3/CH4 switch on the
[Back of
back of the VCR to match the channel se-
the vCR]
lected on the TV.
I
3 Turn on the VCR
I
Press the POWER button to turn on the VCR. Both the
POWER indicator
and the VCR/TV
indicator on the I
VCR come on.
[
mw
_
_
4
Select "ENGLISH" or"ESPAIqOL"
Select
"ENGLISH"
or
t "ESPAiqOL"-Spanish
by using
the PLAY/& or STOP/•
button.
Then, press the F.FWD/I_
but-
ton.
i. EsOt_tH
_1
ESP_UOL
Note: This function effects only the language on the
screen menu and not the audio source.
5
Begin channel preset
f"
o,0,"_
J
PresstheF.FWD/IP"buttononce.
% I /
The tuner scans and memorizes
--i_'_
--
all active channels in your area.
• The VCR distinguishes
between standard TV chart-
nels and cable channels.
i++l
The tuner stops on the lowest
memorized
channel.
The TV
screen returns to TV mode.
• If "AUTO SET UP" appears on the TV screen again,
check the cable connections.
Press the F.FWD/I_-
button once again and the VCR will begin preset
again.
TO SELECT
A DESIRED
CHANNEL
You can select the desired channel by using the CHAN-
NEL • or • button or directly pressing the number but-
tons on the remote control.
Note for using the number buttons:
• When selecting cable channels which are higher than
99, press the +100 button first, then press the last two
digits. (Example: to select channel 125, first press the
+100 button then press '_2" and "5'_).
• You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
-14-
EN
9J27
H58MO
Advertisement
Table of Contents
