Table of Contents
Advertisement
.
SAW_()_TO_
SWITCH:
Thi,s_swit_h i_used to turn the saw motor on and
off_ __,,_
'_L ._ _
NOTE:_Pdsl_i_ing off either the Saw Motor Switch
or the Master Switch will shut off power to the
saw motor.
NOTE: Only the _-].
and JOG keys will work
when the
Saw Motor
Switch
is "ON".
The
elevation only is displayed as long as this switch
is "ON".
Operation
of this switch
is the same as the
Master Switch except for the yellow key.
WARNING: Do not stand in line with blade when
turning switch on.
Do not cycle motor switch "ON"
and "OFF"
rapidly, as this may cause the sawblade
to
loosen. In the event this should occur, allow the
sawblade
to come to a complete stop
and
retighten
the
arbor
nut
normally,
not
excessively.
Never leave the saw with power "ON".
The
display
information.
WARNING:
FOR YOUR OWN SAFETY,
LOWER
BLADE
OR
OTHER
CUTTING
TOOL
BELOW
TABLE SURFACE. (IF BLADE IS TILTED, RETURN
IT TO VERTICAL (0 °) POSITION).
ALWAYS LOCK
THE SWITCH "OFF". WHEN SAW IS NOT IN USE..
• REMOVE KEY AND KEEP IT IN A SAFE PLACE...
ALSO...
IN THE EVENT OF A POWER FAILURE
(ALL OF YOUR LIGHTS GO OUT) TURN SWITCH
OFF...
LOCK IT AND REMOVE THE KEY. THIS
WILL PREVENT
THE SAW FROM STARTING
UP
AGAIN WHEN THE POWER COMES BACK ON.
3. DISPLAY:
NOTE: Readout on display is in decimals. There isa
conversion
chart
for
converting
fractions
to
decimals
on page 55 of this manual.
MINUS
INDICATOR
NUMBERS
OTOR
li
)
II °#°vC
n
DECIMAL
POINTS
gives
the
user
four
pieces
of
1. The
decimal
point
shows
what
function,
oithor I::LEV OR BEVEL,
io b_ing
displayed.
2. The
numbers
show
either
the
present
position
of
the
blade
or
the
entered
destination
for programmed
operation.
3. The
minus
indicator
in the upper
left hand
corner
lights
when
the displayed
number
is
negative
(less
than
the
"zero"
position)
or
when
the
_
key
is pressed
after
a
number.
4. The flashing
IS indicates
that the saw needs
calibrating.
The
flashing"
E" will
only
be
displayed
when the saw requires
calibrating
due to either a power interruption
or the saw
has been unplugged.
FLASHING
"P"
INDICATES
CALIBRATION
REQUIRED
_OTOR
__
-
4. CONTROL
KEYS:
The two rows of keys directly
under the display
are the control
keys. They are how you tell the
computer
what you want it to do.
MINUS
A. Jog
key is a rocker
type switch
that when
pushed
up and held in causes the blade to
elevate when in _
or to bevel to the left
when in _
. Themotionsaretheopposite
when thekey
is pushed down.
When the jog key is pressed and immediately
released
it will cause the blade to change
elevation by 0.005" or bevel by 0.1 ° depending
on the function
selected. This "'tapping" of the
jog key can be repeated
as many times as
desired to move blade into position.
B. _
and
_
keys are used to select the
desired function,
Pressing
_
will display
current
blade
elevation.
Saw must
be in elevation
mode
before any programmed
or
.
jogging elevation
operation
can be pertormed.
A lighted
decimal above
[_
key indicates that the
elevation
function
is active,
In the same way, pressing
_
will display
the current angle of the blade and allow any
programmed
or jogging
bevel operation
to be
performed.
A lighted
decimal
above
[_
indicates that the bevel mode is active
C. _
key is a dual purpose key. When the
saw is first plugged in or if there has been a
power
interruption
the key operates
as a
"Calibration"
key. Pressing the key, with the
24
Hide quick links:
Advertisement
Table of Contents
