Download Print this page

Craftsman 113.29991 Operating And Parts Manual

Bench saw 10-inch tilting arbor
Hide thumbs

Advertisement

OPERATING
INSTRUCTIONS
AND
PARTS LIST FOR
CRAFTSMAN
BENCH
SAW
10-INCH
TILTING
ARBOR
MODEL
NUMBER
i13.29991
The above Model Number will be found on a plate attached to your
saw, at the back, near the bottom of the base. Always mention the
Model
Number when communicating
with us regarding
your saw or
when ordering
parts.
HOW
TO
ORDER
REPAIR
PARTS
All parts listed herein may be ordered through Sears, Roebuck and Co.
o......
p_y,,o-.,e,_r° Limit._d. When ordering parts by mail from the mail
order house which serves the territory in which you live, selling prices
will be furnished on request or parts will be shipped at prevailing prices
and you will be billed accordingly.
WHEN
ORDERING
REPAIR PARTS, ALWAYS
GIVE
THE FOLLOW-
ING
INFORMATION
AS SHOWN
IN
THIS LIST:
1. The PART NUMBER
3. The MODEL NUMBER 113.29991
2. The PART NAME
4. The NAME of item--lO
INCH BENCH SAW
COAST
TO
COAST
NATION-WIDE
SERVICE
FROM
SEARS
FOR
YOUR
CRAFTSMAN
BENCH SAW
SEARS,
ROEBUCK
AND
CO.
and
SIMPSONS-SEARS
LIMITED in Canada
back up your investment with quick,
expert mechanical
service and genu-
ine CRAFTSMAN
replacement
parts.
If and when you need repairs or serv-
ice, call on us to protect your invest-
ment in this fine piece of equipment.
SEARS, ROEBUCK
AND
CO.-
U. S. A.
IN
CANADA,
SIMPSONS-SEARS
LIMITED
Printed in U.S.A.

Advertisement

loading

  Related Manuals for Craftsman 113.29991

  Summary of Contents for Craftsman 113.29991

  • Page 1 SIMPSONS-SEARS LIMITED in Canada back up your investment with quick, expert mechanical service and genu- ine CRAFTSMAN replacement parts. If and when you need repairs or serv- ice, call on us to protect your invest- ment in this fine piece of equipment.
  • Page 2 CRAFTSMAN BENCH SAW, INCH TILTING ARBOR, MODEL 113.29991 Figure --2--...
  • Page 3 CRAFTSMAN BENCH SAW, INCH TILTING ARBOR MODEL 113.29991 WHEN ORbERING REPAIR PARTS, ALWAYS GIVE FOLLO_F1NG INFORMATION AS SHOWN IN THIS LIST: 1. The PART NUMBER. 2. The PART NAME. 3. The MODEL /_UMBER--II3.29991. 4. The NAME of item-10 _ Bench Saw.
  • Page 4 This is necessary because there are two bar alignment springs which act on the inner lip of the rack to hold the fence in continuous alignment. Your Craftsman Saw is shipped complete (without motor Slide fence along rack, noting clearance...
  • Page 5 If not, rotate the tilt hand wheel clockwise until the poifxtx_•. :_ ter indicates approximately 25 degrees on the tilt gage, i Loosen the two set screws m the stop collar nearest the end of the tilt screw (Key No. 55, fig. 1) and repeat The following controls should be tested until the opera- the previous...
  • Page 6 to' the right of the blade the left indicator will read t" etc. When ADJUSTING TILT GAGE _USing saw blade at the rip fence is to the left of the an accurate square, right angles to table top. Then adjust blade the procedure is the same the pointer...
  • Page 7 RESAWING Resawing is the cutting of thick HN' ' 7 RIPPING -- up to 5_/_-inch maximum width Ripping is the sawing of wood with the grain. It is --can be resawed in one pass; generally done with the help of a fence as a guide to '_ but larger boards up to 6l_.ihch maximum require twopasses, position and maintain...
  • Page 8 inch wide can be cut. Outside blades can be used alone, CROSSCUTTING -- Continued chippers cannot. covers table in front of blade_ th_ ;_'' ; When using a full set of dado blades, it is permissible gage should be reversed. to eliminate the loose collar (Key No.