Motor Specifications And Electrical Requirements; Connecting To Power Source Outlet; Contents - Craftsman 113.290650 Owner's Manual

MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS
This saw is designed'to use a 3450 RPM motor only.
Do not use any motor that runs faster than 3450
RPM. It is wired for operation on 110-120volts, 60
Hz., alternating current. IT MUST NOT BE
CONVERTED TO OPERATE ON 230 VOLTS.
CONNECTING TO POWER SOURCE OUTLET
This saw must be grounded while in use to protect
the operator from electrical shock.
If power cord is worn or cut, or damaged in anyway,
have it replaced immediately.
Your saw has a plug that looks likethe one below.
3-PRONG PLUG
....... GROUNDING PRONG
PROPERLY GROUNDED
3-PRONG OUTLET
Plug power cord into 110-120V properly grounded
type outlet protected by a 15-amp. time delay or
Circuit-Saver fuse or circuit breaker.
IF YOU ARE NOT SURE THAT YOUR OUTLET IS
PROPERLY GROUNDED, HAVE IT CHECKED BY
A QUALIFIED ELECTRICIAN.
WARNING: DO NOT PERMIT FINGERS TO
TOUCH THE TERMINALS OF PLUG WHEN
INSTALLING OR REMOVING THE PLUG TO OR
FROM THE OUTLET.
WARNING: IF NOT PROPERLY GROUNDED THIS
POWER TOOL CAN HAVE THE POTENTIAL
HAZARD OF ELECTRICAL SHOCK, PARTICU-
LARLY WHEN USED IN DAMP LOCATIONS,
AROUND PLUMBING, OR OUT OF DOORS. IF AN
ELECTRICAL SHOCK OCCURS THERE IS THE
POTENTIAL OF A SECONDARY HAZARD SUCH
AS YOUR HANDS CONTACTING THE
SAWBLADE.
This saw is_equipped with a 3-conductor cord and
grounding type plug which has a grounding prong,
approved by Underwriter's Laboratories and the
Canadian Standards Association. The ground
conductor has a green lug and is attached to the tool
housing at one end and to the ground prong in the
attachment plug at the other end.
This plug requires a mating 3-conductor grounded
type outlet as shown.
If the outlet you are planning to use for this saw is of
the two prong type DO NOT REMOVE OR ALTER
THE GROUNDING PRONG.IN ANY MANNER. Use
an adapter as shown and always connect the
grounding lug to a known ground.
It is recommended that you have a qualified
electrician replace the TWO prong outlet with a
properly grounded THREE prong outlet.
An adapter as shown below is available for
connecting plugs to 2-prong receptacles. The
green grounding lug extended from the adapter
must be connected to a permanent ground such as
to a properly grounded outlet box.
GROUNDING LUG
MAKE SURE THIS IS
3-PRONG _'_ .3TED TO A
PLUG KNOWN GROUND
\
2-PRONG
RECEPTACLE
ADAPTER
NOTE: The adapter illustrated is for use only if you
already have a properly grounded 2-prong
receptacle.
The use of any extension cord will cause some loss
of power: To keep this to a minimum and to prevent
over-heating and motor burn-out, use the table
below to determine the minimum wire size (A.W.G.)
extension cord. Use only 3 wire extension cords
which have 3 prong grounding type plugs and
3-pole receptacles which will accept the plug on the
saw.
1 H.P. MOTOR 110-120V
Extension Cord Length Wire Size A.W.G.
Up to 50 Ft.................. 14
50 to 100 Ft.................. 12
100 - 200 Ft.................. 10
200 - 400 Ft.................... 8
CONTENTS
Warranty .................................... 2
General Safety Instructions
For Power Tools ........................... 2
Additional Safety Instructions
For Table Saw ............................. 3
Motor Specifications And
Electrical Requirements .................... 5
Unpacking And Checking Contents ........... 6
Assembly .................................... 8
Getting To Know Your Saw .................. 22
Location And Function of
Electronic Controls ..................... 22
Location And Function of
Mechanical Controls .................... 23
Basic Saw Operation ........................ 27
Calibrating The Saw For
Electronic Operations ................... 29
Recommended Accessories ................. 40
Maintenance ................................ 41
Lubrication ................................. 41
Trouble Shooting ........................... 42
Repai r Parts ................................ 46