List Of Error Codes - Brother RH-9800 Instruction Manual

6-7. List of error codes

If the buzzer sounds and an error code starting with "E" appears in the front panel display, check according to
the table below.
Codes E-00 to E-16 are errors which are displayed when the power is turned on. Codes E-30 to E-59 are resetting errors
which are displayed before operation and after the EMERGENCY STOP switch is pressed. Codes E-60 to E-89
represent errors which occur during operation.
Code
E-00 EMERGENCY STOP switch was pressed.
E-02 Machine head is raised (safety switch is off).
E-03 Cloth presser switch was pressed.
E-04 Start switch was pressed.
E-05 RESET button was pressed.
Sewing specifications changeover harness and stitch length
E-09
changeover harness and PROM version do not match.
E-10 Needle bar is not at the highest position.
E-12 Cutting block is lowered.
E-15 Lower thread and gimp trimming knife does not retract.
E-16 Upper thread trimming knife does not retract.
E-30 EMERGENCY STOP switch was pressed.
E-32 Machine head is raised (safety switch is off).
E-35 RESET button was pressed.
E-40 Needle bar has not been raised.
E-42 Cutting block is lowered.
E-45 Lower thread and gimp trimming knife does not retract.
E-46 Upper thread trimming knife does not retract.
E-50 X axis is not at the home position.
E-51 Y axis is not at the home position.
E-52 axis is not at the home position
E-59 Sewing data has been corrupted (checked for each program).
E-60 EMERGENCY STOP switch was pressed.
E-62 Machine head is raised (safety switch is off).
E-69 Needle bar does not stop at the highest position.
E-70 Needle up signal does not turn on and off during operation.
E-71 Needle down signal does not turn on and off during operation.
E-72 Cutting block operation is incorrect.
E-75 Lower thread and trimming operations are incorrect.
E-76 Upper thread operation is incorrect.
When the feed bracket returns to the home position, the X axis is
E-80
not at the home position.
When the feed bracket returns to the home position, the Y axis is
E-81
not at the home position.
When the feed bracket returns to the home position, the axis is
E-82
not at the home position.
E-89 Machine operation direction is reversed.
E-91 Pulse motor overcurrent
Note: Errors E-50, E-51 and E-52 are not errors to be reset after the EMERGENCY STOP switch is pressed.
6. USING THE OPERATION PANEL AND FRONT PANEL
Explanation
RH-9800
Resetting method
Press the EMERGENCY STOP switch once
more and then press the RESET button.
Turn off the power.
Release the cloth presser switch and then
press the RESET button.
Release the start switch and then press
the RESET button.
Turn off the power.
Turn off the power.
Raise the needle to the needle up position
and then press the RESET button.
Turn off the power.
Turn off the power.
Turn off the power.
Press the EMERGENCY STOP switch once
more and then press the RESET button.
Turn off the power.
Turn off the power and then press the
RESET button.
Raise the needle to the needle up position
and then press the RESET button.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Press the RESET button (to interrupt) or
the start switch (to continue).
Turn off the power.
Raise the needle to the needle up position
and then press the start switch (to continue).
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
Turn off the power.
29