Table of Contents
Advertisement
14 TABLE OF ERROR CODES
14 TABLE OF ERROR CODES
If a problem should occur with the bonding machine, the buzzer will sound and an error code and error message will appear
in the operation panel.
Follow the remedy procedure to eliminate the cause of the problem.
Code
E035
The treadle was still being depressed when the
power was turned on.
E036
The feed speed adjustment switch is not at the
neutral position when the power was turned on,
or the switch is faulty.
E065
An operation panel key was still being pressed
when the power was turned on, or key is faulty.
E066
The hand switch was still being pressed when
the power was turned on, or switch is faulty.
E072
The feed speed adjustment switch is not at the
neutral position when gluing starts.
E081
Nozzle cap was not attached properly.
E085
Melter cover was not attached properly.
E090
Treadle connection is faulty.
E091
The adjustment value for the treadle position is
abnormal.
E200
The upper roller motor has gone out of step.
E210
The lower roller motor has gone out of step.
E220
Pump motor is out of step.
E240
The upper roller pressure is outside the
allowable range.
E270
Nozzle clearance adjustment home position
cannot be detected.
E271
Nozzle clearance adjustment motor has
stopped due to a problem.
E290
Displayed when gluing is carried out
continuously for 3 minutes or more.
E410
Communication error detected between the
main PCB and the panel PCB.
E412
Communication error detected between the
main PCB and the temperature control PCB.
E415
Communication error detected between the
main P.C. board and the expansion P.C. board.
E420
No USB media is inserted.
E422
An error occurred while reading from USB
media.
E424
Not enough free space in the USB media.
E425
An error occurred while writing to USB media.
E440
Problem with the EEPROM on the main PCB.
112
Cause
BM-2000
Remedy
If the treadle is being depressed, return it to the
neutral position.
If the treadle is not being depressed, turn off the
power and check that the treadle is not being
pressed.
Check that the feed speed adjustment switch is at
the neutral position.
If it is not at the neutral position, return it to the
neutral position.
Turn off the power, and then check that none of the
keys on the operation panel are being pressed.
Turn off the power, and then check that the hand
switch is not being depressed.
Move the feed speed adjustment switch to the
neutral position.
Check that the nozzle cap is attached correctly.
Check that the melter cover is attached correctly.
Turn off the power, and then check that connector
P8 on the main PCB is properly connected.
Turn off the power, and then adjust the treadle.
Turn off the power and check that the upper roller
turns smoothly.
Turn off the power and check that the lower roller
turns smoothly.
Clean the nozzle discharge holes.
Adjust the upper roller pressure so that it is within
the range set by memory switches No. 573 and No.
574 (for technicians).
Turn off the power and check that the nozzle
clearance adjustment motor is connected to
connector CN20 on the expansion P. C. board.
Turn off the power and check that the lower roller
arm moves smoothly.
Turn the power off and then back on again.
Turn the power off and then back on again.
If this does not solve the problem, turn off the
power, and then check that connector P5 on the
main P.C. board is properly inserted.
Turn the power off and then back on again.
If this does not solve the problem, turn off the
power, and then check that connector CN9 on the
expansion P.C. board and connector CN14 on the
temperature adjustment P. C. board are properly
inserted.
Turn the power off and then back on again.
If this does not solve the problem, turn off the
power, and then check that connector P23 on the
main P.C. board and connector CN25 on the
expansion P. C. board are properly inserted.
Insert the USB media into the USB port of the
operation panel.
Check the files in the USB media.
Increase the amount of free space.
Use the specified USB media.
Turn the power off and then back on again.
Advertisement
Table of Contents
