Introduction Before You Begin - Hayward Pro Logic Installation Manual

Automation and chlorination
Hide thumbs Also See for Pro Logic:
Table of Contents

Advertisement

Introduction
Before You Begin
What's Included
Before attempting to install the Pro Logic system, check that the following components have been included in the
package:
Pro Logic Electronics Unit
(3) Temperature sensors with 15 ft. (5m) cable, hose clamp
Pro Logic Expansion Unit (PS-16 only)
What's NOT Included
Some of the additional items that you may need to complete an installation include:
Circuit breakers
None are included with control—see page 12 and inside of door for suitable breakers
Wire
4-conductor cable (electronics unit to remote display/keypad)
Wire/conduit for 100A service from main panel to Pro Logic
Wire/conduit for filter pump and other high voltage loads
Wire for bonding
Miscellaneous
Utility electrical outlet and weatherproof cover (for mounting on side of Pro Logic)
Mounting hardware (screws, etc.) for mounting Pro Logic and remote display/keypad
Valves (use standard Hayward, Pentair/Compool, or Jandy valves)
Additional valve actuators
Accessory Products - Order Separately
T-CELL-3
Pick N Mix
TM
Chlorinator Cell (for pools up to 15k gallons)
T-CELL-9
Pick N Mix Chlorinator Cell (for pools up to 25k gallons)
T-CELL-15
Pick N Mix Chlorinator Cell (for pools up to 40k gallons)
P-KIT
Chlorination Plumbing Kit containing flow switch and cell unions
AQL-CHEM
ORP & pH sense kit
AQL-CHEM2(-240)
pH dispense kit
AQL2-Wx-PS-4
Wired Remote Display (see note 1)
AQL2-Wx-PS-8
Wired Remote Display (see note 2)
AQL2-Wx-PS-16
Wired Remote Display (see note 3)
AQL2-POD
Handheld Wireless Remote Control (see note 4)
AQL2-Wx-RF-PS-4
Wireless Wallmount Remote Control (see notes 1, 4, 5)
AQL2-Wx-RF-PS-8
Wireless Wallmount Remote Control (see notes 2, 4, 5)
AQL2-Wx-RF-PS-16
Wireless Wallmount Remote Control (see notes 3, 4, 5)
AQL2-Tx-RF-PS-4 (x=W/B) Wireless Table Top Remote Control, specify color - white or black (see notes 1,4,5)
AQL2-Tx-RF-PS-8 (x=W/B) Wireless Table Top Remote Control, specify color - white or black (see notes 2,4,5)
AQL2-Tx-RF-PS-16(x=W/B) Wireless Table Top Remote Control, specify color - white or black (see notes 3,4,5)
AQL-SS-6B-x (x=W/B)
Wired Spa Side 6 Function Remote Control, 150ft cable, spec. color (white or black)
AQL-SS-D-x (x=W/B)
Wired Spa Side 8 Function Remote Control, 150ft cable, spec. color (white or black)
AQL2-SS-RF
Wireless Spa Side Remote Control (see note 4)
AQL2-BASE-RF
Base Station
AQL-DIM
Light Dimmer Relay
AQL-COLOR-MODHV
ColorLogic Network Module for 120V Generation 4 ColorLogic lights
GV A-24
Valve Actuator
V&A-xx
Valve & Actuator (xx=1P (1.5" pos. seal), -2P (2" pos. seal))
GLX-PC-12-KIT
10K thermistor sensor w/15' leads, (necessary if both solar and dual equipment is desired)
Notes:
1. for use with PS-4 model only
2. for use with PS-8 model only
3. for use with PS-16 model only
4. requires base station AQL2-BASE-RF
5. 9V wall plug-in power supply included
1
The display will periodically indicate that the filter pump is on for heater cooldown and show the minutes
remaining.
The pump will automatically turn off at the end of the 5 minute heater cooldown period.
For more detailed instructions on control and operation of the Pro Logic system, refer to the Operation Manual.
Service Mode
Service mode disables all automatic control operation and is intended to be used when servicing the pool system.
To enter service mode, push the SERVICE button once on the main unit keypad. This will initially turn all outputs
off and then allow you to turn outputs on/off manually at the main display (only). In service mode, the buttons on
the optional remote display/keypad and the optional spa side remote will turn outputs off, but will not turn any
output on. Heater control outputs and solar control outputs are prevented from turning on if the water temperature
exceeds 104ºF (40ºC).
Pushing the SERVICE button again will enter a timed service mode. Service operation as described above will
continue for 3 hours, then automatically return to normal operation.
Push the SERVICE button once more to exit out of Service mode.
42

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents