Diagnostic Test; Gprs Communication Test; Lan Connection Test - Visonic POWERMAXCOMPLETE - INSTALLER GUIDE Manual

(see figure 4.1a)
9. DEFINE VOICE
CUST. ZONES NAME
RECORD SPEECH
HOUSE IDENTITY
- don't release
RECORD A MESSAGE
(*)
TALK NOW
(e.g. "John's house")
RECORDING ENDED
(**)
Release button [2]
VOICE BOX MODE
No Voice Box
Voice Box Only
Voice Box Mixed

4.10 DIAGNOSTIC TEST

This mode allows you to test the function of all protected
area wireless sensors / wireless sirens / wireless keypads /
GPRS / LAN connection / options for resetting the
Broadband Module and to receive / review information
regarding the received signal strength.
The diagnostic test process is shown in figure 4.10.
For WL Sensors / WL Sirens / WL Keypads:
Three reception levels are sensed and reported.
Received Signal Strength Indication:
Reception Buzzer Response
Strong Happy Tune twice ( - - - –––– ) ( - - - ––––)
Good Happy Tune ( - - - –––– )
Poor Sad tune ( –––––––– )
IMPORTANT! Reliable reception must be assured. Therefore,
a "poor" signal strength is not acceptable. If you get a
"poor" signal from a certain wireless unit, re-locate it and re-
test until a "good" or "strong" signal strength is received. This
principle should be followed during the initial testing and also
throughout subsequent system maintenance.

4.10.1 GPRS Communication Test

The GPRS Communication diagnostic procedure tests
GSM/GPRS communication and reports the diagnostic
result. In case of
information of the failure is reported.
The following GSM/ GPRS messages are reported:
Message Description
Unit is OK GSM / GPRS is functioning correctly.
GSM comm. The GSM/GPRS module does not
loss communicate with the Panel
Pin code fail Missing or wrong PIN code.
(Only if SIM card PIN code is enabled.)
GSM net. fail Unit failed with registration to local
GSM network.
SIM card fail SIM not installed or SIM card failure.
28
EDIT USER TERM 1 EDIT USER TERM 2
To edit User Terms, use the following buttons on the control panel keypad:
press
press to change from small caps to big caps; press
press to move to the front of the field; press
press to move to the next letter; press
USER #5 NAME
Record users 5 - 8 names (for example, David, Rose, Mark, etc.).
The process is identical to HOUSE IDENTITY recording process.
(*)
USER TERM #1
Record users terms 1-5 (e.g. Living room, Library, etc.), identical to HOUSE IDENTITY recording process.
(*) RECORD MESSAGE is displayed momentarily. The dark square boxes slowly disappear,
one by one, until end of recording time.
(**) To check the recorded message, press the
Figure 4.9 - Speech Recording Flow Chart
communication failure,
EDIT USER TERM 3
to scroll backward; press
USER #6 NAME
USER TERM #2 USER TERM #3
Message
GSM not
detected
No GPRS
service
GPRS conn.
fail
Srvr
unavailable
IP not defined
APN not
defined
SIM card
locked
Denied by
server

4.10.2 LAN Connection Test

detailed The LAN
Broadband Module communication to the IPMP and
reports the diagnostic result. In case of communication
failure, detailed information of the failure is reported.
If the Broadband Module is not registered to the
PowerMaxComplete, the menu "LAN CONNECT.TEST"
will not be displayed.
EDIT USER TERM 4
to scroll forward ;
to delete a character / add a space
to move to the end of the field
to move backward; press
USER #7 NAME USER #8 NAME
USER TERM #4
key and listen to the playback.
Description
GSM auto enroll failed to detect
GSM/GPRS module.
The SIM card does not have the GPRS
service enabled.
Local GPRS network is not available
or, wrong setting to GPRS APN, user
and/or password.
IPMP Receiver cannot be reached –
Check the Server IP
Server IP #1 and #2 are not configured.
APN is not configured.
After entering a wrong PIN code 3
consecutive times the SIM is locked.
To unlock it enter a PUK number. The
PUK number cannot be entered by the
PowerMaxComplete.
The IPMP denies
request. Check that the Panel is
registered to the IPMP Receiver.
Connection diagnostic
EDIT USER TERM 5
to clear the field
USER TERM #5
the connection
procedure tests
D-302754