Recording Speech; Mode Description And Activation; Recording Procedure; Diagnostic Test - Visonic POWERMAX Programming Manual

• Select the factors that will activate each X-10 unit. The
list of factors is the same as for the PGM output (see
Para. 7.2 above).
Note: Each X-10 unit may be programmed for activation
by any combination of factors.
Having gained access to DEFINE X-10 (see Para. 7.1 B),
proceed as follows:
A. Click <OK> while DEFINE X-10 is displayed. The
display will show:
S E T H O U S E C O D E
B. Click <OK> again. The display will read:
h o u s e c o d e = X
The "X" represents a letter from A to P and the dark box
means that this letter is the current choice.
C. Click <NEXT> or <BACK> repeatedly to reach the
desired code letter. When it is on display, click <OK>
twice. The display will revert to Set House Code. Then
click <NEXT>. The display will change to:
D E V I C E C O D E
The system controls up to seven X-10 units. If you click
<OK> now, code No. 1 will be selected automatically:

8. RECORDING SPEECH

8.1 Mode Description and Activation

This mode allows you to record short-duration speech
messages for two purposes:
• House identity is a message announced automatically
when events are reported to private telephones.
3 custom zone names can be recorded and assigned
•
to specific zones. These names prove useful if none of
the 26 fixed zone names are found suitable for a
certain zone (see Para. 4.2, Step G.).
To activate the recording mode, proceed as follows:
A. Upon gaining access to the installer menu (see Section
1), the display will read "1. NEW INSTL CODE".
B. Click <NEXT> until the 7th mode is displayed:
7 . R E C O R D S P E E C H

8.2 Recording Procedure

Having gained access to the RECORD SPEECH mode,
you can now record the house identity.
A. Click <OK>. The display will change into:
H O U S E I D E N T I T Y
B. Press the <2> key until this is displayed briefly:

9. DIAGNOSTIC TEST

9.1 Mode Description and Activation
This mode allows you to test the function of all wireless
sensors deployed throughout the protected area, to collect
information about the received signal strength from each
transmitter and to review accumulated data after the test.
The diagnostic test is designed to sense and report 3
reception levels as shown in the following table:
DE5450P
c o d e n o . 1
D. Click <NEXT> or <BACK> to select any other code.
Once the desired code is displayed, click <OK>. The
display will change to:
O N B Y A R M I N G
E. Continue as in Paragraph 7.2, Steps C through P, until
you finish defining the factors that will activate the
selected X-10 unit. When done, Click <HOME> to
select any other X-10 unit and program the factors that
will activate it the same way as you did for the first one.
F. Once you are through dealing with all 7 (or just all
relevant) device codes, you have completed a full cycle
of the DEFINE OUTPUTS mode.
If at this point you wish to return to the
installer's menu, click <AWAY>. This will get
you back to:
< O K > T O E X I T
You may now review and select any other
mode on the installer's menu (by clicking
<NEXT> or <BACK>).
R E C O R D A M E S S A G E
Immediately thereafter, the display will change into:
T A L K N O W
C. Do not release the <2> key and start talking
immediately, while facing the front panel. The dark
square boxes will slowly disappear one by one, from
right to left. When the last one disappears (5 seconds
later) the following message will be displayed:
R E C O R D I N G E N D E D
D. Release the <2> key. To check the message, press the
<5> key and listen to the playback.
E. Click <NEXT>. The display will change into:
U S E R T E R M # 1
F. Record the first customized zone name as in Steps B
through D above (recording duration is 3 seconds only).
G. Click <NEXT> and repeat the procedure for the 2
rd
zone name and 3
<HOME> to return to the main menu.
You may now click <NEXT> to test the system (see
Section 9).
Reception Buzzer Response
Strong Happy Tune twice ( - - - –––– ) ( - - - ––––)
Good Happy Tune ( - - - –––– )
Sad Tune ( –––––––– )
Poor
To activate the diagnostic mode, proceed as follows:
zone name. When done, click
nd
17