Diagnostic Test; Gprs Communication Test; Lan Connection Test - Visonic POWERMAX PRO Installer's Manual

4.10 DIAGNOSTIC TEST

This mode allows you to test the function of all protected
area wireless sensors / wireless sirens / wireless keypads /
GPRS / LAN connection / options for resetting the
Broadband Module and to receive / review information
regarding the received signal strength.
The diagnostic test process is shown in figure 4.10.
For WL Sensors / WL Sirens / WL Keypads:
Three reception levels are sensed and reported.
Received Signal Strength Indication:
Reception Buzzer Response
Strong Happy Tune twice ( - - - –––– ) ( - - - ––––)
Good Happy Tune ( - - - –––– )
Poor Sad tune ( –––––––– )
IMPORTANT! Reliable reception must be assured. Therefore,
a "poor" signal strength is not acceptable. If you get a
"poor" signal from a certain wireless unit, re-locate it and re-
test until a "good" or "strong" signal strength is received. This
principle should be followed during the initial testing and also
throughout subsequent system maintenance.

4.10.1 GPRS Communication Test

The GPRS Communication diagnostic procedure tests
GSM/GPRS communication and reports the diagnostic
result. In case of
information of the failure is reported.
The following GSM/ GPRS messages are reported:
Message Description
Unit is OK GSM / GPRS is functioning correctly.
GSM comm. The GSM/GPRS module does not
loss communicate with the Panel
Pin code fail Missing or wrong PIN code.
(Only if SIM card PIN code is enabled.)
GSM net. fail Unit failed with registration to local
GSM network.
SIM card fail SIM not installed or SIM card failure.
GSM not GSM auto enroll failed to detect
detected GSM/GPRS module.
No GPRS The SIM card does not have the GPRS
service service enabled.
GPRS conn. Local GPRS network is not available
fail or, wrong setting to GPRS APN, user
and/or password.
Srvr IPMP Receiver cannot be reached –
unavailable Check the Server IP
IP not defined Server IP #1 and #2 are not configured.
APN not APN is not configured.
defined
SIM card After entering a wrong PIN code 3
locked consecutive times the SIM is locked.
To unlock it enter a PUK number. The
PUK number cannot be entered by the
PowerMax Pro.
Denied by The
server request. Check that the Panel is
registered to the IPMP Receiver.
28
communication failure,
IPMP denies the

4.10.2 LAN Connection Test

The LAN
Broadband Module communication to the IPMP and
reports the diagnostic result. In case of communication
failure, detailed information of the failure is reported.
If the Broadband Module is not registered to the PowerMax
Pro, the menu "LAN CONNECT.TEST" will not be
displayed.
The following LAN messages are reported:
Message
Unit is ok
Test aborted
Comm. loss
detailed
Rcvr Ip
missing
Cable
unplugged
Check lan
config
Rcvr#1
UnReach.
Rcvr#2
UnReach.
Rcvr#1 UnReg.
Rcvr#2 UnReg.
Broadband
Module
timeout err.
Invalid result
connection
Connection diagnostic
Description
Broadband Module
correctly.
The diagnostic test is aborted, as
follows:
• AC failure – Broadband Module is
set to OFF mode.
• Broadband
Module
completed the power-up procedure.
In this case, the installer should wait
a maximum of 30 seconds before
re-testing.
The RS-232 serial interface between
the Broadband
PowerMax Pro failed.
Receivers IP 1 and 2 settings are
missing in the PowerMax Pro.
The Ethernet cable is not connected
to the Broadband Module.
This message appears in any of the
following cases:
• Incorrect Broadband Module IP has
been entered.
• Incorrect subnet mask has been
entered.
• Incorrect default gateway has been
entered.
• DHCP server failure.
Receiver 1 or 2 is inaccessible, as
follows:
• Wrong receiver IP has been entered.
• Receiver failure.
• WAN Network failure.
The PowerMax
registered to IP receiver 1 or 2.
Broadband Module does not respond
to test result within 70 sec.
Broadband Module responds with a
result code that is not recognized by the
PowerMax Pro.
procedure tests
is functioning
has not
Module and the
Pro unit is not
D-302541