Panasonic AG-HPX300 Operating Instructions Manual page 72

Information Item
11. Camera Warning and
Report Area
(related to AWB, ABB
and switch settings)
(Switch changeover
indication)
(Low light warning)
(Y GET value)
(MARKER indication) MKR: A/B/OFF
12. User button
functions
UM: USER MAIN
button
U1: USER1 button
U2: USER2 button
72 Adjustments and Settings for Recording : Viewfinder Screen Status Displays
Indication
AWB A ACTIVE
AWB B ACTIVE
AWB A OK ¢ . ¢ K
AWB B OK ¢ . ¢ K
AWB BREAK ¢ . ¢ K
AWB NG
COLOR TEMP LOW
COLOR TEMP HIGH
LEVEL OVER
LOW LIGHT
TIME OVER
ATW MODE
AWB PRESET ¢ . ¢ K
CHECK FILTER
ABB ACTIVE
ABB OK
ABB BREAK
ABB NG
B-SHD READY
B-SHD ACTIVE
B-SHD OK
B-SHD BREAK
B-SHD NG
WHITE: # ¢ . ¢ K
AUTO KNEE: ON/OFF
DRS: ON/OFF
GAIN: ¢¢ dB
SS: 1/ ¢¢¢¢ or ¢¢¢ . ¢ deg
SS: 1 1/ ¢¢¢¢ or 1¢¢¢ .0d
CC: ¢¢¢¢ ¢¢ K
ND: ¢
EXTENDER: ON/OFF
IRIS: ¢¢ F ¢ . ¢
LOW LIGHT
¢¢¢ . ¢ %
INH
S.GAIN ¢¢ dB/OFF
DS.GAIN ¢¢: /OFF
S.IRIS ON/OFF
I.OVR ON/OFF
S.BLK – ¢¢ /OFF
B.GAMMA ON/OFF
AUDIO CH1
AUDIO CH2
REC SW
Y GET ON
RET SW
SLOT SEL
PRE REC
USB HOST/DEVICE/OFF
DRS ON/OFF
ASSIST ON/OFF
C.TEMP
AWB being performed on Ch A.
AWB being performed on Ch B.
AWB successful on Ch A.
AWB successful on Ch B.
AWB action aborted by user.
AWB action failed. The second line indicates the status.
Color temperature too low.
Color temperature too high.
Brightness too high.
Brightness too low.
Action timed-out.
This is indicated when AWB cannot be executed since ATW is being
operated.
AWB cannot be performed because the AWB switch is position at PRE or
the super gain is enabled.
Make sure the FILTER control is positioned correctly.
ABB being performed.
ABB action successful.
ABB action aborted by user.
ABB action failed.
Black shading accepted (by holding down the ABB switch during ABB
adjustment).
Black shading being adjusted.
Black shading adjustment successful.
Black shading adjustment aborted by user.
Black shading adjustment failed.
The WHITE BAL switch has been switched. # is replaced with A, B or PRST.
When [A] and [B] are set to "VAR", then it is indicated as VAR ¢ . ¢ K. When
[B] is assigned ATW, then it is indicated as ATW MODE.
Displayed when the AUTO KNEE switch is assigned to ON or OFF and the
AUTO KNEE switch is turned ON/OFF.
Displayed when the AUTO KNEE switch is assigned to DRS and the AUTO
KNEE switch is turned ON/OFF.
Gain has been switched with the GAIN selector switch or a user button.
When the shutter speed has been switched, the shutter speed is indicated.
Shutter speed is in SYNCRO SCAN mode.
This appears when the CC filter setting has been selected.
This appears when the ND filter setting has been selected.
Lens extender has been turned on or off.
Indicated when the iris override correction value is to be changed.
Brightness too low.
With the Y GET ON setting, the output brightness level near the center
marker is displayed as "%."
Current marker type
User buttons disabled.
Selected S.GAIN
Selected DS.GAIN
Whether S.IRIS is ON or OFF.
Iris override can be set (the IRIS OVERRIDE setting is ON).
Status of SUPER BLACK (ON or OFF). When it is ON, the set value is also
indicated.
Status of BLACK GAMMA (shade correction for the black level): ON or OFF
Input signal to be recorded on Audio Channel 1 has been switched.
Input signal to be recorded on Audio Channel 2 has been switched.
USER button acts as REC switch.
Y GET function ON.
USER button acts as RET switch.
Switch that changes the target card is set.
Indicates that PRE-RECORDING mode has been switched ON or OFF.
USB action status has been switched.
Indicates whether the dynamic range stretcher function is ON or OFF.
Indicates whether the focus assist function is ON or OFF.
Indicates the mode for changing the color temperature with the JOG dial
button is ON or OFF.
Status