Panasonic AG-HPX300 Operating Instructions Manual page 22

32.
DVCPRO connector
This is an in/output connector for video, voice, and
data that comply with the IEEE1394 standard. It is
impossible to input/output the DV signal.
Notes
Power is not supplied from the unit.
Be absolutely sure to bear the following points in
mind when connecting the IEEE1394 cable (DV
cable).
Ensure that the connections with other devices are
made on a 1:1 basis.
When an IEEE1394 cable has been connected to
the DVCPRO connector, do not apply any strong
external force as this may damage the connector.
When error code 1394 E-92 (1394 INITIAL
ERROR) appears, disconnect the connecting
cables and re-connect them or turn off the
camera-recorder's power and turn it back on.
Ensure that the unit and all of the connected
devices are each grounded (or connected to a
common ground) before use.
If it is not possible to ground the unit and devices,
turn off the power of the unit and of all the
connected
disconnecting the IEEE1394 cable.
When the unit is to be connected to a device
equipped with a 4-pin type of connector, connect
the unit's connector (6-pin type) first.
When connecting the unit
with a PC equipped with
a 6-pin type ofconnector,
connect the IEEE1394
cable as dictated by the
shapes of
connectors. Bear in mind
that inserting a plug the wrong way round may
damage the unit.
When the unit is used in AVC-Intra format, image/
voice signals cannot be output/input through the
DVCPRO connector.
33.
REMOTE (remote control) connector
The remote control
accessory) is connected here.
Note
For software of the AJ-RC10G, use Version 1.10-00-
000 or higher.
34.
OPTION SLOT
Attach the video
optional). For information about the installation and
proxy recording, see the AJ-YAX800G instruction
manual.
22
Parts and their Functions Shooting and Recording/Playback Functions Section
devices before connecting
6-pin type
the 1394
4-pin type
unit AJ-RC10G
encoder card (AJ-YAX800G,
35.
SD memory card insertion slot
An SD memory card (optional accessory) is inserted
here. SD memory cards are used for uploading meta-
data, and proxy recording (optional).
<Cautions in using SD memory cards>
Use the unit by inserting an SD memory card that is
compliant with the SD standard or the SDHC standard.
MultiMediaCards cannot be used. (Bear in mind that
taking pictures may no longer be possible if you do use
them.)
If you intend to use miniSD cards in camera-recorder,
always install the adapter specially designed for
miniSD cards. (The unit will not work properly if only
the miniSD card adapter is installed. Make sure that
the card has been installed in the adapter before using
it.)
Use of Panasonic's SD memory cards and miniSD
cards is recommended. Be sure to format cards using
camera-recorder.
To format SD memory cards using a personal
computer, download the dedicated software from the
support site.
Any SD memory card with the following capacities (8
MB to 2 GB) and any 4 GB SDHC memory card can
or
be used with the unit.
8 MB
128 MB
2 GB
To record proxy (optional), use an SD memory card with
a capacity of 256 MB, 512 MB, 1 GB, or 2 GB labeled
"High Speed" or use a 4 GB SDHC memory card.
For the latest information not available in the operating
Instructions, visit the P2 Support Desk at the following
Web sites.
https://eww.pavc.panasonic.co.jp/pro-av/
The SDHC card conforms to a new standard for memory
cards with a large capacity of more than 2 GB which was
established by the SD Association in 2006.
The SD card logo is a registered trademark.
MMC (MultiMediaCard) is a registered trademark of Infineon
Technologies AG.
(optional
36.
BUSY (operation mode display) lamp
This lamp indicates the active status of the SD
memory card.
It stays illuminated when the card is active.
Note
While the lamp is on, do not insert or remove the card.
16 MB 32 MB
256 MB 512 MB
4 GB (SDHC)
64 MB
1 GB