Panasonic AG-HPX300 Operating Instructions Manual page 151

9. 1394 Error
The 1394 E- ¢¢ indicator in the display
Display window
window blinks. For more information, see
indication
[1394 Error Codes] (page 152).
Blinks 4 times per second while the
WARNING lamp
WARNING lamp recording is continuing.
Blinks 4 times per second while the TALLY
Tally lamp
LAMP recording is continuing.
In the case of Error Code 92, "1394 INITIAL
ERROR" indicator lights up (during pause
and recording)
Viewfinder
For Error Codes other than Error Code 92, or
if REC SIGNAL is set to "1394", no error is
displayed in the viewfinder.
Beeps 4 times per second while ALARM
Warning tone
recording is continuing.
This indicates a failure of the DVCPRO
Warning
connector.
description
The operation continues, but input signals to
Recording/
the DVCPRO connector are abnormal. For
playback
more information, see [1394 Error Codes]
operation
(page 152).
Check the connection between the
IEEE1394 cable and the DVCPRO
connector, settings of any external device
Countermeasures and menus, and the turn on the power again.
If the warning indication is still illuminated,
confirm the " 1394 Error Codes " (page 152),
and consult your distributor.
10. Battery Nearly Empty
Display window One of the bars in the battery remaining
indication indicator starts blinking.
WARNING lamp Blinks once per second.
Tally lamp Blinks once per second.
Viewfinder The BATT LED blinks.
Warning tone Beeps 4 times per second.
Warning
The battery is about to run out.
description
Recording/
playback Continues to operate.
operation
Countermeasures Replace the battery as required.
11. P2 Card Nearly Full
Display window One of the bars for remaining MEDIA
capacity starts blinking.
indication
Blinks once per second while recording
WARNING lamp
continues.
Blinks once per second while recording
Tally lamp
continues.
Viewfinder The P2 card remaining capacity indicator blinks.
Beeps once per second while recording
Warning tone
continues.
Warning The total remaining capacity of all the P2
description cards is two minutes or less.
Recording/
Continues to operate.
playback
operation
Replace the cards. If there is an empty card
Countermeasures
slot, insert a new card.
12. P2 Card Error
If the error occurs during recording,
"00:0000:11" appears as the time code
Display window indication. The indication continues to flash
indication after recording is stopped and until the next
operation is performed. There is no
indication if the error occurs during playback.
If the error occurs during recording, the lamp
flashes four times per second for a period of
WARNING lamp
about three seconds. The lamp does not
light if the error occurs during playback.
If the error occurs during recording, the lamp
flashes four times per second for a period of
Tally lamp
about three seconds. The lamp does not
light if the error occurs during playback.
A flashing "CARD ERR ¢ " appears. In the
actual indication the ¢ is replaced by the slot
Viewfinder
number of the P2 card that triggered the error.
If the error occurs during recording, the tone
sounds four times per second for a period of
Warning tone
about three seconds. The tone does not
sound if the error occurs during playback.
Warning
An error has occurred while recording data
description to or playing data from a P2 card.
Recording/ Stop recording or playback. After recording
playback is stopped, the P2 card where error occurs is
write protected.
operation
Countermeasures Replace the affected P2 card.
13. FAN STOP
No display.
Display window
indication
Blinks 4 times per second.
WARNING lamp
No display.
Tally lamp
The FAN STOP indicator blinks while
Viewfinder
recording continues.
It does not sound.
Warning tone
The fan is at rest because something is
Warning
wrong with it.
description
If the camera-recorder operates with the fan
Recording/ stopped, then the temperature inside rises.
playback While the camera-recorder continues to
operation operate, clips may not be recorded or played
back properly.
Immediately stop using the camera-recorder
Countermeasures
and consult your distributor.
Maintenance and Inspections : Warning System
151