Panasonic AG-HPX300 Operating Instructions Manual page 185

MIC/AUDIO2
Items/ Adjustable
Data Saved Range
ON Select the phantom power supply for the
FRONT MIC
front microphone.
POWER OFF
– C U F –
REAR MIC ON Select the phantom power supply for the
POWER OFF rear microphone.
When OFF is selected, no phantom
power is supplied even if the REAR
AUDIO CH1 or CH2 switch is set to +48.
– C U F –
STEREO When the MONITOR switch is set to ST
MONITOR
MIX (stereo), select the signal format for the
SELECT
monitor output.
– C U F –
FRONT MIC –40dB Select the front microphone input level.
LEVEL –50dB
– C U F –
REAR MIC –50dB Select the rear microphone input level.
–60dB
CH1 LVL
– C U F –
Select the rear microphone input level.
REAR MIC –50dB
CH2 LVL –60dB
– C U F –
REAR LINE IN +4dB Select the rear line input level.
LVL 0dB
–3dB
– C U F –
+4dB Select the audio output level.
AUDIO OUT
LVL 0dB
–3dB
– C U F –
HEADROOM 18dB Set the headroom (standard level).
20dB
– C U F –
WIRELESS ON Select whether or not to enable the
WARN OFF alarm to trigger for poor wireless
receiver reception.
– C U F –
The ____ in the Adjustable Range column indicates the
preset mode.
Remarks
Data Saved
TC MODE
UB MODE
VITC UB
MODE
TC/UB
Items/ Adjustable
Range
DF Set the time code mode.
NDF DF: Drop frame.
NDF: Non drop frame.
Note
When the camera-recorder operates at
50 Hz or in 24P or 24PA mode, the non-
drop frame is always used.
– C U F –
USER Select the user bits mode.
TIME USER: Select UB value set in the LCD
DATE
TIME: Select
EXT
TCG
DATE: Select local date and time (2 last
FRM RATE
REGEN
EXT:
TCG: TCG value enters UB.
FRM RATE:
Select the shooting information (e.g.
frame rate) for the camera. For more
information, see [Frame rate
information recorded in user bits]
(page 58).
When clips recorded in Native mode
are played back, the frame rate
information recorded in users bits in
the VAUX range is output.
REGEN: Read out value stored in the
– C U F –
USER/EXT Select the user bits mode for VAUX TC
TIME (VITC).
USER/EXT:
DATE
If UB MODE is set to EXT, the EXT
TCG
value is recorded. If not, USER value
FRM RATE
set by UB is recorded.
REGEN
TIME: Select
DATE: Select local date and time (2 last
TCG: TCG value enters UB.
FRM RATE:
Select camera shoting information
(frame rate, etc.). For more
information, see [Frame rate
information recorded in user bits]
(page 58).
REGEN: Read out value stored in card
Note
When the camera-recorder operates in
24P, 24PA, 30P (AVC-I) or 25P (AVC-I)
mode, FRM RATE is always selected.
– C U F –
Menu : Menu Description Tables
Remarks
section.
local time (hours,
minutes, seconds).
digits of year, month, date, time).
When "CAM" , "VIDEO", or
"SDI" is selected in REC
SIGNAL on the SYSTEM MODE
screen, the user bits input to the
TC IN connector are recorded.
When "1394" is selected, the
user bits of signals input to the
DVCPRO connector are
recorded.
If reading fails, USER value is
retained.
card and record value
continuously.
local time (hours,
minutes, seconds).
digits of year, month, date, time).
and record value continuously.
185